BUILT IN THE USA. READY FOR YOUR PROJECT.
Motor Control Centers for Power Plants
Power plants depend on more than generators: pumps, fans and other auxiliary motors support the systems that keep a unit available.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Power plants depend on more than generators: pumps, fans and other auxiliary motors support the systems that keep a unit available. A motor control center (MCC) groups motor feeders and control equipment, but the right arrangement depends on how those auxiliaries behave during startup, normal production and disturbances. Owners and engineers should define those operating conditions before purchasing a new assembly.
Start with the auxiliary load schedule
A useful schedule identifies each motor, its driven equipment, normal and starting current characteristics, operating duty, and whether it runs continuously or intermittently. Include feeder lengths, cable requirements, starting frequency and expected future loads. Distinguish a cooling pump from an infrequently operated service motor: their consequences of interruption and starting demands may be very different.
The plant team should indicate which motors must run together, which have duty and standby partners, and which can wait after a source disturbance. Grouping feeders in one MCC can simplify distribution and supervision, but concentrating critical auxiliaries creates a common dependency. Separate lineups or sources may improve resilience where justified by the plant design, at the cost of more interfaces and equipment.
Account for the generation and auxiliary sources
Show the MCC supply on the plant one-line, including upstream transformers, generators, utility connections and any alternate source. Identify normal and abnormal source configurations and who controls a transfer. A station-service transformer fed from the grid and an auxiliary transformer associated with a generating unit may produce different operating and fault conditions; the design must consider the actual system.
Provide the system voltage, grounding arrangement, load and available fault-current data at the intended connection point for each relevant operating state. Generator contributions and protection behavior can change with plant configuration, so the engineer should evaluate the assembly and protective devices against the project studies rather than rely on a single assumed duty. Confirm equipment ratings and feasibility during review.
Choose starters and coordinate protection
Starter selection affects starting torque, current, motor acceleration and process control. Across-the-line starting may suit some loads, while reduced-voltage starters or variable-frequency drives may be worth evaluating for others. Drives add control flexibility but also introduce considerations such as harmonics, heat and compatible motor cables. Compare the entire operating requirement, not only the starter purchase price.
The MCC design must coordinate each motor feeder’s short-circuit protection and overload protection with the upstream device and motor characteristics. Provide motor data and the protection study assumptions to the equipment designer. The responsible engineer should review coordination over the relevant fault and load range; a protective device that clears a fault does not by itself guarantee selective operation.
Define operating sequences and control interfaces
A plant startup may require lube oil, cooling or ventilation auxiliaries before the generating unit can operate. Document the required sequence, permissives and indications, including the treatment of standby equipment and load shedding when the source is constrained. Identify who owns the sequence: the distributed control system, a local controller or equipment external to the MCC.
For each interface, specify command and status points, alarm behavior, control-power source, communications protocol if needed, and local-versus-remote authority. Explain the desired response to a lost communication link or control supply without assuming a universal fail-safe state. Hardwired interlocks and networked signals have different dependencies; jointly review the cause-and-effect matrix and testing responsibilities.
Plan the room and maintenance access
Locate the proposed lineup on a drawing showing entry routes, shipping sections, cable entry, termination space and access for doors and maintainable components. Room ventilation must account for equipment heat as well as plant ambient conditions. Dust, moisture, washdown, corrosive atmospheres or a classified area can change enclosure and component requirements; describe actual exposure for project-specific selection.
Spares can be provided as installed feeder units or as prepared space, depending on the design and future load information. Installed spares require a larger initial commitment; space alone does not establish future bus capacity or fault-duty suitability. The owner’s maintenance plan and qualified electrical personnel should address isolation, applicable working clearances and any arc-flash study needed for the installation.
Buy against a defined scope and test plan
Send the direct manufacturer the one-line, motor schedule, operating states, environmental criteria and proposed layout with the quotation request. Identify required documentation, preferred components or origin requirements, and applicable assembly standards or listings for verification. Ask for a scope identifying feeder units, control hardware, drawings, inspection and testing, along with explicit exceptions and the interfaces left to others.
Submittals should allow review of elevations, feeder schedules, control schematics, terminals, ratings and the point list before fabrication proceeds. Agree on factory functional checks and records, field wiring and commissioning responsibilities, and the schedule dependencies for approvals and components. Installation, testing and energization require qualified personnel under site procedures; coordinate plant outage and startup windows with the equipment schedule confirmed as the design progresses.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT