BUILT IN THE USA. READY FOR YOUR PROJECT.
Switchgear and Distribution Products
Selecting a distribution assembly starts with the job it must perform, not a product name.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Selecting a distribution assembly starts with the job it must perform, not a product name. A main service, a bank of motors and a critical alternate source each place different demands on switching, protection and space. For owners, contractors and engineers in San Antonio, South Texas and nationwide, the comparison begins with the system one-line and ends with a documented equipment scope.
Choose the main distribution architecture
A switchboard can organize service or feeder distribution in a coordinated assembly of protective devices, bus and terminations. It may fit a project that needs a practical distribution lineup without the particular device construction specified for power circuit breaker switchgear. Compare the actual arrangement, access requirements and protective capabilities rather than treating the names as interchangeable.
Low-voltage switchgear may be specified where power circuit breaker features, compartmentation or maintainability are important. Those features depend on the proposed construction and devices; drawout equipment is not automatic. Compare interrupting and withstand duties, protective functions and physical space alongside cost. Coordination between protective devices requires a project-specific study, not a product-family label.
Separate branch distribution from motor control
Panelboards generally distribute power to downstream branch circuits or smaller feeder groups, often near the loads they serve. A main switchboard and several panelboards can therefore be complementary rather than competing choices. Identify circuit counts, panel locations and feeder paths early; concentrating everything in one large lineup may increase cable runs or crowd the electrical room.
A motor control center groups motor-related control and protection functions, potentially including starters or interfaces to drives, according to the design. A plant with pumps, conveyors or fans may need both upstream distribution and an MCC. Provide motor schedules, starting requirements, control-voltage preferences and any process control interfaces so the boundary between assemblies is clear.
Match voltage and construction to the system
Medium-voltage distribution calls for equipment selected around the system voltage class, fault duty, switching function and protection scheme. Metal-clad and metal-enclosed construction are not synonyms: metal-clad equipment has more specific construction and compartmentation requirements. The specifying engineer should identify the applicable equipment standard and whether the proposed arrangement meets the project’s maintenance objectives.
An outdoor pad-mounted arrangement raises different questions from an indoor lineup, including site access, environmental exposure, foundation details and utility interfaces. High-voltage requirements warrant an early feasibility discussion rather than an assumed catalog match. For every family, confirm actual ratings, available configurations and any required listing for the specific proposed assembly.
Account for source transfer and distribution paths
An automatic transfer switch selects between normal and alternate sources under an agreed sequence; it does not replace the need to evaluate upstream and downstream protection. Document generator start signals, source capacities, neutral and grounding arrangements, operating states and monitoring points. The project engineer should resolve these interfaces with the transfer equipment and distribution assembly suppliers.
Busway provides another distribution path where the design calls for it, while cables offer routing flexibility that may suit other layouts. Compare available space, support and expansion provisions, connection geometry and installation responsibilities. If a busway connection is proposed, show the mating flange, phase arrangement and dimensional tolerances on coordinated drawings rather than assuming field fit.
Establish the electrical and physical basis
Supply a current one-line, load and feeder schedules, nominal system voltage, phase and wire configuration, source details and available fault-current information. Include planned growth and the protection or coordination criteria. The manufacturer and project engineer can then review device interrupting capability and assembly fault duty together, as well as continuous-current and environmental requirements.
Room dimensions, access routes, top or bottom cable entry and conductor quantities can change the lineup even when the electrical duty stays the same. Outdoor exposure, heat, ventilation, working clearances and shipping splits also need review. The installer and design team should verify site conditions and applicable requirements before a layout is released.
Compare proposals on scope and schedule
When purchasing new equipment directly from a manufacturer, request a defined equipment boundary, device schedule, drawings, applicable standards, inspection and test scope, and documented exceptions. For an appropriate switchboard, specify any required UL 891 listing and verify that the proposed assembly and configuration have the project-specific listing. Other product families require their own applicable standards review.
Clarify who supplies field cables, foundations, settings, installation and commissioning, and establish drawing-review milestones before the delivery sequence is planned. If US-made components are required, identify the documentation and exceptions process; actual sourcing and availability need confirmation. Qualified electrical personnel must plan and perform field work under site procedures, applicable codes and manufacturer instructions.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT