AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

347/600V Switchgear: Application and Load Planning

A 347/600 V distribution plan starts with the actual source and the loads it must serve, not with a voltage label alone.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Electrical switchgear beneath overhead conduits in an industrial room.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A 347/600 V distribution plan starts with the actual source and the loads it must serve, not with a voltage label alone. Engineers, contractors and owners should distinguish line-to-line utilization from line-to-neutral utilization, then translate the load schedule into equipment, protection and installation requirements. A direct manufacturer can evaluate a new assembly against those project-specific inputs; availability at this voltage must be confirmed.

Identify the source and its grounding

A typical 347/600 V system is a three-phase wye supply: nominally 600 V between phases and 347 V between a phase and the neutral. The designation does not establish that a neutral is brought to every assembly or that a particular grounding arrangement applies. Obtain the utility or transformer secondary configuration, grounding method, phase sequence and conductor count.

Mark source transformers, disconnecting points and each proposed distribution assembly on the one-line diagram. If an alternate source or tie is planned, show its voltage, grounding and intended operating states as well. The engineer must resolve any incompatible source configurations and confirm utility and local authority requirements before the equipment is specified.

Separate loads by connection and operating pattern

A three-phase motor or balanced heater may use the 600 V phase-to-phase supply, while a compatible lighting load can use 347 V from phase to neutral. Record each load’s nameplate voltage, phase, full-load current or power, starting method and duty. Do not assume a piece of utilization equipment accepts either voltage merely because it is near the distribution lineup.

Other loads may need a separate transformer and downstream distribution rather than a direct connection. Include transformer capacity and secondary loads in the schedule, but avoid counting the same load twice at the upstream bus. Note loads that run together, seasonal peaks and planned additions so the design team can apply appropriate demand assumptions.

Translate the schedule into capacity

For illustration, a balanced 60 kW resistive three-phase heater at 600 V draws about 58 A per line at unity power factor. That is operating current, not a breaker or bus selection. Motor efficiency, power factor, starting current, continuous-load requirements and applicable code rules can change the design calculation for other loads.

For a facility expansion, distinguish confirmed loads from placeholders and assign each an expected connection date. Present spare feeder positions and spare bus capacity as separate requests: an empty compartment alone does not prove the assembly can support future demand. Agree on the growth case with the engineer before obtaining comparable quotations.

Review voltage class and fault duty together

The engineer and manufacturer should verify that the proposed assembly, insulation system and individual protective devices suit the system voltage, phase arrangement and grounding. A device marked with a slash voltage rating has application limits that depend on the system and its grounding; a nominal voltage match by itself is not enough. Check controls, meters and surge protection separately.

Request available fault-current information at the installation point, including source contributions and expected changes. Device interrupting capability and the assembly’s applicable short-circuit rating must be evaluated with the protective scheme and any required coordination study. Determine which party supplies study data and settings; do not substitute a continuous-current rating for a fault-duty assessment.

Plan neutral and connection interfaces

Where phase-to-neutral loads are served, show the neutral path, conductor quantities and termination needs on the drawings. Unbalanced lighting and nonlinear electronic loads can affect neutral current and heating, so neutral sizing belongs in the project design rather than an assumed percentage. Coordinate grounding and bonding with the engineer and applicable service requirements.

Cable entry direction, conductor size and number, bending space and lug compatibility affect the physical lineup even when electrical ratings are acceptable. Confirm room dimensions, access clearances, ventilation, delivery splits and the transformer or busway interface. These details should be reviewed early with the installer, not left until construction drawings are complete.

Define quote and approval deliverables

Send the manufacturer the one-line, load schedule, source and fault data, room layout, environmental conditions and required metering or control interfaces. Ask for a quotation that identifies device and assembly ratings, included studies or tests, assumptions and exceptions. For an appropriate switchboard, verify any required UL 891 listing for the specific configuration rather than assuming it applies to every switchgear assembly.

Schedule time for engineering review, submittal approval, component procurement, fabrication and project-specific inspection; unresolved voltage or interface questions can affect each stage. Establish who provides installation, protection settings, field testing and final records. Qualified electrical personnel must perform installation and commissioning under the site safety plan and applicable requirements.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote