AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Custom Switchgear Quote

A useful custom switchgear quote starts with more than an equipment name.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Electrical cabinets and overhead cables lining a long industrial aisle.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A useful custom switchgear quote starts with more than an equipment name. The manufacturer must translate the project’s electrical design, physical constraints and purchasing requirements into a defined new assembly. Owners, engineers and contractors in San Antonio, South Texas and nationwide can shorten the clarification cycle by identifying what is known, what remains provisional and who will resolve each open item.

Show the power system, not just the lineup

Send the latest one-line diagram with its revision and indicate the equipment boundary to be quoted. Identify utility, transformer, generator or other sources; normal and alternate operating states; main and tie devices; and feeder destinations. Provide nominal system voltage, phase and wire configuration, grounding arrangement, and intended continuous current for each section where established.

Available fault current and source characteristics are equally important. Supply the utility information and any short-circuit study, noting the date and assumptions. The engineer and manufacturer need to assess interrupting duty and assembly withstand against the proposed system; a continuous-current figure by itself cannot establish fault-duty suitability. Flag protection coordination requirements and identify who will perform the study.

Turn load information into a feeder scope

A feeder schedule should show circuit destinations, proposed protective devices, load characteristics and any known conductor quantities. Describe significant motors, starting methods and nonlinear loads, plus anticipated additions and realistic demand assumptions. The design engineer can use these inputs to evaluate capacity and protection rather than relying on an arbitrary growth allowance.

Decide whether future circuits need installed devices, equipped spaces or only room for a later design review. Each option changes the initial purchase and the ease of expansion; empty physical space alone does not establish available bus capacity or fault duty. Identify required metering, alarms and protective functions so these items are priced instead of assumed.

Make the room and delivery path part of the quote

Provide a dimensioned room or site plan showing the proposed footprint, height restrictions, access doors and cable entry direction. The project team must check required working clearances and maintenance access against the applicable code and actual equipment arrangement. Include indoor or outdoor location, ambient conditions, moisture and corrosive exposure, together with any ventilation constraints.

For restricted routes, describe loading access, lift limits and the path from the delivery vehicle to the foundation. Shipping sections may make transport possible but introduce field alignment and connection work. Ask the proposal to identify anticipated shipping splits, preliminary dimensions and weights, and responsibility for receiving, rigging, anchorage and field assembly.

Define electrical and control interfaces

Terminations affect both enclosure layout and installation effort. Provide conductor material, size and number per phase where known, entry location, and any transformer or busway connection requirements. Show the intended boundary between manufacturer-supplied connections and contractor-installed cable, supports and grounding. Ask for unresolved interface dimensions to be marked on the submittal drawings.

If the equipment serves as service entrance, share utility metering rules and approval requirements with the design team. For remote monitoring or source transfer, identify control power, communications protocol, points, interlocks and the party supplying each external device. Agree on intended operating states and responsibility for integrating and testing signals with the site system.

Ask for comparable scope and evidence

A meaningful proposal should describe the equipment type, electrical characteristics, principal devices, enclosure, included options and specific exclusions. Request drawings and a bill of materials at the agreed stage, along with any exceptions to the specification. Compare competing scopes on the same basis: a lower initial quote may omit metering, inspection, documentation or field services another proposal includes.

State the applicable equipment standard and required listing in the request. UL 891 may be relevant to an appropriate switchboard assembly; verify the proposed assembly’s project-specific listing and scope rather than applying it to every type of switchgear. Define factory inspection or functional test expectations, witness arrangements, acceptance criteria and the records to be delivered.

Connect approvals and schedule to the purchase

Share the required delivery window and the dates for design review, utility acceptance and purchase authorization. Ask which milestones depend on approved drawings, component availability, fabrication, testing and transportation. A proposed schedule is an estimate based on those inputs, not a guarantee; late revisions or unresolved interfaces can change both cost and timing.

Assign an owner for each open question and use revision-controlled drawings and a written change process after approval. For occupied facilities, coordinate installation and any outage planning with the owner and contractor. Qualified electrical personnel should perform field work, testing and energization under the site’s safety procedures; clarify whether commissioning, protection settings and final documentation are included or separately supplied.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote