BUILT IN THE USA. READY FOR YOUR PROJECT.
Motor Control Centers: Selection and Equipment Scope
A motor control center (MCC) brings the controls and protection for multiple motors into a coordinated assembly.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A motor control center (MCC) brings the controls and protection for multiple motors into a coordinated assembly. It can simplify a plant’s motor distribution, but selecting one means more than counting motors or reserving floor space. Owners, engineers and contractors need to agree on the electrical supply, how each machine starts and stops, the surrounding environment, and who is responsible for the field interfaces.
Start with the motor and source schedule
Provide a one-line showing the source, upstream protective device, grounding arrangement and MCC feeder, together with the available fault current at the proposed location. Identify system voltage and phase, the desired main device and incoming cable arrangement. The engineer can then assess bus and assembly ratings against the actual system rather than selecting equipment by motor count.
For every pump, fan or other motor, list nameplate data, full-load current, operating duty, starting method and driven equipment. Note which motors run together, restart automatically or must remain available on an alternate source. Present loads and credible expansion plans help establish demand and bus capacity; adding motor nameplate currents alone does not resolve the design.
Choose starters for the process
An across-the-line starter may suit a motor that can tolerate its starting current and mechanical acceleration. A soft starter can reduce starting stress for some applications, while a variable-frequency drive can control speed when the process benefits from it. Compare the operating requirement, motor compatibility and supply-system effects, not just the initial device cost.
Drives also introduce questions about heat, ventilation, harmonics and motor cable arrangements. Specify whether a bypass is needed and how the process should respond to a drive fault. Larger or more complex control units can consume more vertical section space, so a lineup with the same number of motors may have a substantially different footprint.
Match protection and unit construction
Each motor branch needs an engineered combination of short-circuit protection, motor control and overload protection appropriate to the application. Provide motor data, upstream protection details and any coordination-study requirements. The device interrupting capability and the complete assembly short-circuit rating must be evaluated against available fault current; an individual component rating alone does not establish the assembly rating.
Compare fixed and removable unit arrangements where the proposed construction supports them. Removable units may improve future service flexibility, but their interfaces, interlocks and space provisions must match the assembled design. Confirm applicable MCC standards and any required listing for the exact configuration; maintenance or unit removal remains subject to the owner’s safety procedures.
Define controls and outside connections
Identify which functions are local and which originate in a programmable controller or building system. A useful control narrative states the intended start permissives, stop commands, status indications, alarms and response to loss of control power. Separately identify safety functions and the party responsible for their design, validation and integration with the machinery.
Specify control voltage, terminal points, communication protocol and network ownership before drawings are finalized. For a pump station, for example, level controls and remote run feedback may come from another panel; the MCC scope should state who supplies the field devices, interconnecting conductors, programming and end-to-end functional checks.
Fit the lineup to the installation
Give the manufacturer room dimensions, entry routes, cable entry direction, mounting constraints and the expected ambient conditions. Dust, moisture, corrosive exposure and heat can change enclosure and ventilation choices. Coordinate heat rejection with the room designer, and have the electrical designer verify applicable working clearances and access for the selected equipment.
Request an elevation showing unit locations, cable termination areas and shipping splits. Spare unit space can ease expansion, but it is not proof that the bus, source or feeder has capacity for another motor. Document reserved physical space and electrical capacity separately, including any future control or communications interfaces.
Buy against a defined scope
A direct manufacturer can develop a meaningful proposal from the one-line, motor schedule, site constraints and required documentation. Ask for a unit schedule, component descriptions, ratings, outline drawings, control schematics and a clear list of exceptions. Compare proposals on equivalent protection, starter functions, enclosure features, spare provisions and field connection responsibilities, rather than on section count alone.
Agree on the drawing approval sequence, component availability review, factory inspection and any specified functional testing or witness requirements. Clarify delivery and rigging boundaries, field wiring, settings, commissioning and turnover records. Schedule depends on released design information and procurement decisions, so resolve substitutions and changes promptly; qualified electrical personnel must perform installation, testing and energization under site procedures.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT