AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

2,000-Amp Switchgear: Protection and Fault-Duty Review

A 2,000-ampere designation describes a proposed continuous-current class, not the fault current an assembly can safely handle.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Electrical cabinets and overhead cables lining a long industrial aisle.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A 2,000-ampere designation describes a proposed continuous-current class, not the fault current an assembly can safely handle. For a new distribution lineup, purchasing decisions should connect the load, source configurations and protective devices to documented short-circuit and coordination studies. A direct manufacturer can review the proposed scope, but the actual assembly ratings and availability require project-specific engineering confirmation.

Separate normal current from fault duty

The main bus and equipment may be intended to carry up to a specified continuous current under defined conditions. That number alone does not establish the interrupting rating of a breaker or the short-circuit rating of the assembled lineup. Ambient conditions, enclosure design, connected devices and applicable equipment standards all matter when engineering confirms the final construction.

Ask the project engineer to distinguish the required main bus current, main protective device rating and trip setting from feeder sizes. A lineup may serve varied loads through smaller feeders, and an adjustable trip unit does not by itself increase the capacity of the bus or the fault duty of the assembly. Confirm each required rating on approved submittals.

Establish the fault current at each source

Request the utility fault contribution and its assumptions, transformer impedance and size, conductor information, and any generator or motor contribution. The study provider uses these inputs to calculate available fault current at the proposed equipment and relevant downstream locations. Document the date and basis of the utility data rather than treating an old value as permanent.

Evaluate credible operating arrangements, including a closed tie or alternate source if the design permits them. A configuration with more sources can raise available fault current; a weaker source can produce less current, affecting protective sensitivity and clearing time. Have the engineer identify both the maximum and minimum cases needed for the proposed protection scheme.

Match devices and the complete assembly

The selected interrupting device must be suitable for the system voltage and the fault duty at its location. The complete assembly also needs an appropriate short-circuit rating, including the bus and its supports. Where a short-time withstand rating is specified, its associated time matters: protection must clear faults within the verified capability of the equipment.

A higher interrupting rating or stronger bus construction may affect device selection, size and cost. Current-limiting fuses or a tested series-rated combination may be options, but their use depends on the exact devices, assembly, application and applicable rules. Do not assume that an upstream protective device automatically makes a lower-rated downstream device acceptable.

Coordinate protection across the distribution system

A coordination study compares protective-device characteristics over the range of fault currents at each location. The objective is to let the device nearest a fault clear it while upstream equipment remains available where practicable or where required. Supply device types, trip-unit functions, transformer data and downstream protection information early enough to influence selection.

There can be tension between selective coordination and rapid fault clearing. Longer delays may preserve service to unaffected feeders but can increase incident energy or exceed a short-time withstand limit. Instantaneous functions can limit clearing time but may reduce selectivity at higher fault currents. The engineer should document the resulting tradeoffs and any project-specific coordination requirements.

Resolve grounding, controls and study interfaces

Ground-fault protection depends on the system grounding arrangement, sensing locations and applicable requirements. A main, tie and multiple sources may require particular attention to neutral paths and sensor coordination. Provide grounding diagrams and the intended source operating states so the engineer can review the scheme rather than specifying devices from current rating alone.

If protection uses external relays, clarify current-transformer data, trip-power source, wiring terminals, alarms and who supplies settings. Also define the boundary between the assembly manufacturer, study provider and field contractor. Factory checks can verify agreed wiring and functions, while site-specific settings and field acceptance remain separately assigned responsibilities.

Buy against an approved protection package

Send the manufacturer the one-line diagram, load and feeder schedule, required voltage and phase configuration, available-fault-current data, source operating modes and desired study scope. Request a proposal identifying main and feeder devices, assembly ratings, drawings, exceptions, testing and documentation. If a switchboard is specified, verify whether UL 891 listing is appropriate and confirm the proposed assembly’s project-specific listing.

Allow time for utility information, study revisions, submittal review, device availability and approval of changes before manufacturing and delivery dates are finalized. At handoff, retain approved drawings, test records and final protection settings for commissioning. Qualified electrical personnel should perform installation, verification and energization under applicable codes, site safety procedures and manufacturer instructions.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote