BUILT IN THE USA. READY FOR YOUR PROJECT.
Service Entrance Switchgear: One-Line and Feeder Planning
A service-entrance one-line is more than a drawing of breakers and buses.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A service-entrance one-line is more than a drawing of breakers and buses. It defines where utility supply becomes the customer’s distribution system and how power reaches each major load. For an owner, electrical engineer, or contractor, an accurate diagram helps a manufacturer quote new equipment that fits the service arrangement, feeder routes, and realistic expansion plans.
Begin at the utility connection
Identify the source, nominal system voltage, phase and wire configuration, transformer location, and proposed service point. Show whether supply reaches the assembly by cable or busway and identify the utility/customer ownership boundary. Utility requirements for service arrangement, metering, access, and approval can affect the lineup before its dimensions are settled.
Ask the utility for the available fault-current information and the assumptions behind it, including anticipated service changes where known. The engineer uses that information to evaluate equipment and protective-device duties. A service diagram that shows only a main current value cannot establish the required interrupting or assembly short-circuit performance.
Draw the service and metering interfaces
Show the proposed service disconnecting arrangement, metering location, and any instrument transformer compartment or separate utility enclosure. Distinguish utility revenue metering from customer monitoring: their physical access, wiring, and approval requirements may differ. Confirm who supplies meters, instrument transformers, and associated wiring rather than assuming they are included.
The one-line should also identify neutral and grounding arrangements and the intended service grounding and bonding interfaces. The engineer and authority having jurisdiction determine the applicable requirements; the manufacturer needs these decisions to coordinate buses, terminals, and compartments. A diagram should not substitute for the detailed grounding design.
Give every feeder a destination
Label each outgoing circuit with its destination, load type, proposed protective device, and required capacity. A feeder serving a motor-control center can have different starting and protection considerations from one feeding a lighting panel. Include large motors, nonlinear loads, and continuous loads in the supporting schedule so the engineer can assess their effect.
Separate connected load from calculated demand, and document diversity assumptions instead of adding nameplate values without context. Show alternate sources and transfer equipment where applicable, including how their circuits connect to the distribution system. Source capacity and permitted operating arrangements need review; a one-line alone does not establish an acceptable transfer sequence.
Coordinate conductors with the physical lineup
For incoming and outgoing circuits, provide the proposed conductor material, size, number of parallel sets, insulation, and entry direction when known. The manufacturer can then review terminal provisions, bending space, and compartment layout. A compact electrical diagram may otherwise conceal a termination area that cannot accommodate the planned cables.
Top entry may simplify an overhead route but compete with structural or cable-tray space; bottom entry may depend on a suitable slab, trench, or conduit arrangement. Coordinate neutral and equipment-grounding conductor terminations as well as phase conductors. The installer and design team should verify routing, clearances, and field connection responsibilities.
Reserve growth without assuming capacity
Show expected future loads by destination and approximate demand, with the owner’s timing assumptions. A spare protective device can support a known future feeder, while a prepared space may defer that device purchase. An empty space is not automatically a usable circuit: the bus, fault duty, terminals, and approved construction still need to accommodate the addition.
Compare the cost and footprint of reserved sections with the risk of a later expansion. Oversizing the lineup alone does not increase utility transformer capacity or service conductor capacity. Have the engineer check the complete upstream path and protection coordination, and identify which future requirements remain assumptions in the quote.
Turn the diagram into a purchasing scope
Send the direct manufacturer the current one-line, load and feeder schedules, utility criteria, fault data, room constraints, and required milestones. Request a proposal identifying equipment boundaries, ratings to be engineered, included devices, meter provisions, exceptions, and submittals. For an appropriate switchboard, verify the project-specific listing and whether UL 891 applies.
Allow time for utility and engineering review, drawing revisions, component procurement, fabrication, and agreed testing; changes to feeder count or cable entry can affect the schedule. Request approved drawings, connection details, and test records for handoff. Qualified electrical personnel should perform installation, verification, and energization under the site’s procedures and applicable requirements.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT