BUILT IN THE USA. READY FOR YOUR PROJECT.
Medium-Voltage Switchgear
Medium-voltage switchgear brings switching, protection and distribution together at an electrical system’s primary distribution level.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Medium-voltage switchgear brings switching, protection and distribution together at an electrical system’s primary distribution level. Its design depends on more than the voltage shown on a one-line diagram: source fault contribution, feeder duties, protection philosophy and physical interfaces all affect the assembly. Engineers, contractors and owners can work directly with a manufacturer of new equipment to define these details before requesting a firm project scope.
Choose the switching arrangement first
Start with a one-line showing incoming sources, buses, transformers, feeder destinations and any tie connection. Identify normal and alternate operating configurations, critical loads and planned expansion. A single-source radial lineup can be simpler than a main-tie-main arrangement, but it may offer fewer options for isolating a section while maintaining service elsewhere.
Construction is a separate decision. Metal-clad designs generally provide compartmentation and may use withdrawable circuit breakers; other metal-enclosed arrangements can use switches and fuses. Compare protection functions, isolation provisions, maintenance access, footprint and cost rather than treating these descriptions as interchangeable. The manufacturer should confirm which construction and devices are feasible for the particular specification.
Define voltage and fault duty together
Provide nominal system voltage, frequency, phase configuration and grounding method, along with the utility’s service requirements where applicable. The engineer must select an appropriate equipment voltage class and insulation level for the system and its expected transient conditions. A nominal voltage alone does not establish the assembly’s actual ratings or suitability.
Request current available-fault data at the proposed connection and identify possible future source changes. Breaker interrupting duty, closing and latching duty, and bus short-time withstand are different checks; the duration of withstand must also match the protection scheme. A qualified engineer should review the complete assembly and its components against the study, not just one device nameplate.
Coordinate relays, sensing and controls
Protective relays need suitable current and voltage transformer inputs. Supply the intended protection functions, transformer ratios, accuracy requirements and connected burdens for review; metering and protection may have different needs. The coordination study should account for upstream utility protection and downstream transformer or feeder devices, including the range of system configurations.
Document the trip and control power source, supervision and required response to loss of control power. For remote indications or controls, define the communications protocol, point list, control authority and network boundary. Interlocks and transfer logic should be reviewed against the owner’s operating philosophy, with final relay settings assigned to the responsible engineer.
Plan the room and cable interfaces
Share room dimensions, access routes, floor loading limits and required equipment clearances early. Allow space for doors, cable termination, inspection and the handling of removable devices where the chosen design requires it. Equipment layout must be checked against applicable codes, manufacturer instructions and the actual working conditions, rather than a generic clearance assumption.
Specify indoor or outdoor exposure, ambient conditions, altitude and concerns such as moisture or corrosive atmospheres. Provide cable entry direction, conductor sizes and quantities, shielding and termination requirements, and grounding interfaces. The contractor and manufacturer should reconcile termination space and shipping splits with the civil foundation, rigging route and field connection scope.
Make testing and documentation measurable
Identify the applicable equipment standards and any required listing or certification in the specification, then verify the proposed assembly’s actual scope and evidence. Ask for submittals that include a one-line, elevations, ratings, device schedules, control schematics, terminal details and a clear list of exceptions. Review those documents before releasing designs for fabrication.
Define factory acceptance criteria and whether the owner will witness checks. Depending on the specified assembly, the test plan may address wiring, interlocks, protective functions and dielectric testing. Agree on the records to be delivered and who performs relay testing and field commissioning; factory checks do not replace site-specific acceptance or the engineer’s coordination study.
Buy against a complete project scope
A useful request for quotation includes the one-line, load and fault studies available to date, specifications, site constraints and an anticipated delivery sequence. State required documentation, spare components and any component-origin preferences, including US-made components where specified. Confirm availability and sourcing for the actual bill of materials rather than assuming every part meets a preference.
Compare proposals for engineering, fabrication, testing, freight and exclusions, then schedule review cycles, component procurement, installation and commissioning as linked milestones. Changes to source duty or cable entry can affect both drawings and delivery planning. For projects in San Antonio, South Texas or nationwide, installation, testing and energization must be planned and performed by qualified personnel under applicable site procedures.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT