BUILT IN THE USA. READY FOR YOUR PROJECT.
Current and Voltage Transformers
Current transformers (CTs) and voltage transformers (VTs, sometimes called potential transformers) scale power-system quantities into inputs suitable for meters and protective relays.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Current transformers (CTs) and voltage transformers (VTs, sometimes called potential transformers) scale power-system quantities into inputs suitable for meters and protective relays. A useful specification does more than name a ratio: it defines which devices the signals serve, how accurately they must perform, and where their circuits terminate. For a new distribution assembly, these choices affect protection, physical layout, documentation, and the procurement schedule.
Assign each measurement a purpose
Start with a one-line diagram showing the source, buses, feeders, and proposed sensing locations. Identify whether each measurement supports operating displays, energy reporting, protective functions, or utility billing. A main-bus CT, for example, will not show an individual feeder load; feeder measurements need appropriately located sensors and separate wiring paths.
Metering and protection do not necessarily need the same CT characteristics. Metering emphasizes accuracy over the expected operating range, while protection must provide useful information during faults, when core saturation can distort the signal. Separate cores or circuits may be appropriate; the protection engineer should determine the arrangement rather than assuming one output can serve every purpose.
Select ratios around the actual application
For CTs, provide expected normal and minimum load, projected growth, and the available fault-current information. A ratio selected only for maximum anticipated load can leave ordinary readings at an unnecessarily small fraction of the meter input. Conversely, a ratio chosen for fine low-load resolution may be unsuitable for the protection scheme.
Match the CT secondary rating and any selectable taps to the connected meter or relay inputs. For VTs, provide the system configuration and normal voltage range, then specify the primary-to-secondary ratio required by the receiving devices. The engineer should check insulation, continuous thermal capability and fault-related duties against the actual installation and equipment design.
Make accuracy and burden measurable
State the applicable accuracy classification and standard for each measuring or protective function; classifications from different standards should not be treated as interchangeable without review. For metering, evaluate ratio and phase-angle performance at the load levels that matter. For relays, the protection study should address expected fault levels, relay requirements, and the risk of CT saturation.
Burden is the load presented to a transformer secondary by connected devices and wiring. Ask the designer to account for meter and relay inputs, test facilities, and the complete lead length, using compatible manufacturer data. Longer CT leads can increase burden and affect performance. VT burden and voltage drop also deserve review, especially when several devices share a circuit.
Coordinate sensing and wiring interfaces
Document the phase connections, polarity convention, grounded or ungrounded system arrangement, and voltage signals needed by the meter or relay. VT connection schemes and primary and secondary circuit protection must fit the system and protective functions; a three-phase measurement requirement alone does not establish the correct connection. The engineer should also coordinate any required grounding.
Give the assembly manufacturer a device list, connection diagrams, terminal assignments, and proposed external cable routes. Define which wiring is factory-installed and which is field-connected, including any communications interface from the meter. Identify the utility billing boundary separately: utility approval, transformer ownership, sealing provisions, and access rules can differ from customer monitoring requirements.
Plan physical space and safe access
A CT must physically fit its conductor or bus arrangement, with mounting and cable routing compatible with the assembly design. VTs, protective devices, terminal blocks, and test facilities also need suitable space and access. Decide whether measurements are needed on the main, each feeder, or both before the enclosure layout is finalized.
Instrument circuits can present serious hazards: an energized CT with an open secondary can develop hazardous voltage, and a shorted VT secondary can draw damaging current. Specify appropriate terminals, test provisions, barriers, identification, and access for the intended design. Qualified personnel must perform all installation, testing, and maintenance under site procedures and applicable requirements.
Define the quote and review package
A request to the direct manufacturer should include the one-line, source and load data, fault study information, meter and relay requirements, available physical dimensions, and any utility rules. Identify required ratios, accuracy classes, secondary ratings, burden assumptions, preferred test facilities, and any component-origin requirements; confirm actual sourcing and availability during review.
Request drawings showing sensing locations, wiring and terminal details, device schedules, and documented exceptions. Agree on project-specific inspection and test records, including ratio and polarity checks where specified, and identify who supplies settings and performs field verification. Allow time for utility input, engineering review, component procurement, drawing approval, and commissioning coordination; changes after approval can affect the schedule.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT