AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Meter-Main Equipment Planning

A meter-main assembly brings utility metering and a service disconnect into a coordinated equipment package, but the utility and the electrical design determine how those functions fit together.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Row of Allen-Bradley electrical control cabinets with black handles.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A meter-main assembly brings utility metering and a service disconnect into a coordinated equipment package, but the utility and the electrical design determine how those functions fit together. For engineers, contractors and facility owners, the most useful early decision is not simply an enclosure size: it is establishing the service arrangement, approval path and physical interfaces before equipment is purchased.

Start with the serving utility

Ask the serving utility for its current service and metering requirements, approved equipment criteria and project review process. Confirm the service characteristics, point of delivery, available fault-current information and whether the proposed meter location is acceptable. Requirements can vary by utility and application, so an arrangement accepted elsewhere is not a substitute for project-specific approval.

Show the utility how many meters are proposed, which loads each meter serves and whether future tenants or additions are anticipated. A building with individually metered tenants may need a different equipment layout and approval sequence than a single-account facility. Record who supplies the meter and any instrument transformers, and who is responsible for their installation and inspection.

Choose the metering interface

Depending on the utility and service design, metering may be self-contained or use instrument transformers in a designated compartment. Confirm the utility’s criteria rather than assuming either arrangement will be accepted. The meter mounting provision, transformer compartment, secondary wiring path and sealable access may all affect the assembly dimensions and internal arrangement.

Revenue metering is distinct from an owner’s power-monitoring meter. If both are needed, identify their locations and measurement objectives on the one-line diagram. Utility-controlled compartments can restrict access, so plan any customer monitoring and communications around the approved boundaries rather than assuming a customer device can share the revenue-metering space.

Define disconnects and service boundaries

The design should show the service disconnect or disconnects, their relationship to the meter and the loads they serve. The engineer and authority having jurisdiction must establish the applicable service-disconnect requirements, while the utility confirms its own interface and access rules. An arrangement convenient for tenant billing may not automatically meet every service-equipment requirement.

Identify the service point, grounding and bonding responsibilities, and interfaces to downstream distribution on the drawings. If a generator or other alternate source is part of the project, show the transfer equipment and source boundaries as well. This helps the manufacturer price the intended scope without assuming that external field connections or transfer controls are included.

Match the assembly to the electrical duty

Provide a load calculation, the system voltage and phase configuration, the proposed service capacity, and a one-line showing protective devices and outgoing feeders. Include expected load growth and any large motors or nonlinear loads that deserve engineering review. The calculated demand and future expansion plan should guide the selection, not a meter label alone.

Supply the available fault-current information and its source so the engineer and manufacturer can evaluate the proposed assembly and protective-device ratings together. Specify any required selective coordination or ground-fault functions for review. Where a switchboard is the appropriate assembly, confirm whether a project-specific UL 891 listing is required and verify the listing scope for the proposed configuration.

Plan space, access and installation

Indicate whether the equipment is indoors or outdoors, the exposure conditions, intended mounting surface and cable entry directions. Provide a dimensioned site layout showing the delivery route and relevant obstructions. Cable quantities, sizes and termination arrangements can change the space needed inside the assembly, even when the electrical service capacity stays the same.

Coordinate utility meter access, required working space, enclosure access and any foundation or structural supports with the design team. A compact arrangement may reduce footprint but leave less room for terminations or future feeders. The contractor should review the proposed elevations and connection details against actual site conditions before the drawings are approved.

Buy against a documented schedule and scope

Send the direct manufacturer the one-line, load information, utility requirements, site constraints and desired delivery milestone with the quotation request. Ask for an itemized scope, equipment drawings, device schedule, applicable listing details, testing documentation and identified exceptions. Compare proposals on the same metering provisions and field interfaces, not just their overall dimensions.

Build the schedule around utility review, drawing approval, component availability, production, delivery, inspection and the contractor’s outage plan where needed. Assign ownership of permits, utility coordination, field wiring, protective settings and commissioning. Electrical installation, testing and energization belong to qualified personnel working under applicable codes, site procedures and manufacturer instructions; the equipment submittal should support that handoff.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote