BUILT IN THE USA. READY FOR YOUR PROJECT.
400-Amp Switchgear
A 400-amp switchgear request identifies a nominal current class; it does not establish the actual assembly rating or equipment type.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A 400-amp switchgear request identifies a nominal current class; it does not establish the actual assembly rating or equipment type. For a new power distribution assembly, the design must match the source, connected loads, fault duty and site conditions. Owners, contractors and specifying engineers can work directly with an American manufacturer to define those details before selecting a construction and requesting a quote.
Start with the load, not just the main device
A 400-ampere main device, a bus with a 400-ampere continuous rating and a feeder serving a calculated 400-ampere load are different specifications. Ask the engineer to identify the required ratings of the assembly, main and outgoing circuits separately. Device settings, conductor ratings and permissible loading depend on the complete design and applicable requirements.
Provide a load schedule showing existing and planned demand, operating patterns, motor starting and any significant nonlinear loads. If expansion is likely, describe the expected circuits and timing rather than simply requesting extra space. A spare breaker position cannot, by itself, increase the capacity of the main bus or incoming service.
Define the source and fault duty
The one-line diagram should show each source, the system voltage, phase and wire configuration, grounding arrangement and the proposed main and feeders. For service equipment, include the utility’s service and metering requirements. Alternate sources and transfer equipment also need to be shown, including the intended operating states and any required interlocks.
The engineer needs available fault current at the assembly location and the assumptions behind it, including source and transformer data. Breaker interrupting ratings and the assembly’s applicable short-circuit rating must be suitable for that duty; a 400-amp continuous-current designation says nothing about fault capability. Coordination studies can then evaluate protective devices across the relevant fault range.
Choose the assembly for the job
The term switchgear is sometimes used broadly, but a project may call for a switchboard or another distribution assembly instead. Specify the desired device type, maintenance access, metering and operating functions before comparing proposals. Construction choices influence footprint, accessibility, protection options and cost; the right choice depends on the project rather than amperage alone.
Identify the equipment standard and listing required by the specification and authority having jurisdiction. UL 891 may be relevant to an appropriate switchboard assembly, not automatically to every kind of switchgear. Request confirmation that the proposed configuration and its intended application fall within any required listing; availability and actual ratings require engineering review.
Coordinate terminations and the physical installation
Supply room or site dimensions, equipment access routes, indoor or outdoor exposure, ambient conditions and applicable clearance requirements. Top versus bottom cable entry changes the available bending space and routing. Show the number, size and material of incoming and outgoing conductors, along with grounding and neutral connection requirements, so the proposed terminations can be checked.
A compact lineup can save floor area but leave less room for cable work, metering or future circuits. Review elevation drawings, access arrangements, shipping dimensions, weights and lifting provisions with the installer. If space or transport requires separate shipping sections, identify who will handle field assembly and what instructions and inspections are included.
Make bids and submittals comparable
A useful request includes the one-line, load and feeder schedules, fault-duty information, site constraints and a list of required documents. Ask for the main and feeder device descriptions, bus and enclosure ratings, metering interfaces, specified tests and explicit exceptions. The quotation should distinguish included components from allowances and work assigned to others.
Review drawings for source and feeder connections, equipment dimensions, device functions, ratings and circuit identification before approval. Agree on interfaces for utility metering, remote indications or communications when needed, including who supplies field wiring and configures external systems. A lower initial quote may omit a required study, test or accessory, so compare scope as well as price.
Plan approval, delivery and turnover
Schedule time for engineering questions, submittal review, component availability, fabrication, inspection and shipping. Changes to feeder quantities, protection or site dimensions after approval can affect both cost and delivery. For projects in San Antonio, South Texas or elsewhere nationwide, coordinate receiving access and the installation sequence with the project team rather than assuming a fixed lead time.
Define factory inspection and test criteria, required records, manuals and final drawings in the purchase scope. Assign responsibility for field connections, protection settings, commissioning and acceptance with the owner and contractor. Qualified electrical personnel should perform site work under applicable safety procedures and manufacturer instructions; the engineer and authority determine project-specific requirements before energization.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT