AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Metal-Enclosed Switchgear: New Equipment Replacement Planning

Replacing a metal-enclosed switchgear lineup is not simply a matter of matching its footprint.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Electrical cabinets and overhead cables lining a long industrial aisle.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

Replacing a metal-enclosed switchgear lineup is not simply a matter of matching its footprint. The new assembly must fit the power system, the building and the owner’s planned outage. A direct manufacturer can develop a proposal for newly manufactured equipment from project information, but the owner, engineer and contractor must establish the existing interfaces and confirm that the proposed arrangement is feasible.

Establish the actual connection points

Start with the latest one-line diagram, available equipment drawings and nameplate information. Identify every source and feeder, transformer connection, grounding arrangement, control supply and affected load. Note discrepancies between drawings and facility records; a qualified electrical professional should determine what site verification is needed under the owner’s safety procedures.

For each incoming and outgoing circuit, document the cable quantity and size, entry direction, termination arrangement and available conductor reach. Record external control and communications connections as well as utility-owned interfaces. Existing labels or dimensions alone do not establish that the new equipment can accept the conductors or reproduce the intended operating functions.

Choose switching and protection for the system

Metal-enclosed construction can incorporate different switching devices; it does not by itself specify a breaker, fused switch or the compartmentation associated with metal-clad equipment. The engineer should identify each circuit’s required switching and isolation functions, protection scheme, operating frequency and maintenance objectives before comparing device arrangements.

Provide system voltage, continuous load, available fault-current data, source characteristics and the protection study basis. The manufacturer and engineer can then evaluate assembly and device duties, bus design, relays, instrument transformers and interlocks together. A compact arrangement may save space, while a different configuration may better support access or protection coordination; either requires project-specific review.

Resolve the physical fit before ordering

Measure the proposed equipment area and access route, including doors, turns, lifting limits and potential shipping splits. Show finished floor elevations, existing foundations, nearby obstructions and cable routes. The installer and design team should check applicable working clearances, ventilation and access for the selected devices rather than assuming the previous layout remains suitable.

A lineup that is too short or narrow to accept existing cable bends can create costly field changes. Conversely, adding a transition section may require more floor space and structural work. Coordinate attachment points, enclosure environment, heat dissipation and field connection responsibilities with the civil, mechanical and electrical trades.

Build the outage around owner priorities

The owner should identify critical loads, acceptable interruption windows and dependencies such as process shutdowns or utility approval. The project team can then outline stages for preparation, removal, installation, testing and return to service, including decision points and a contingency if prerequisites are not complete. A phased approach may reduce individual outage windows but add temporary interfaces.

Where continuity is essential, have qualified designers assess temporary power capacity, protection, grounding and connection boundaries. Document who supplies it and who authorizes its use. All isolation, switching and energization remain the responsibility of qualified personnel following the owner’s approved procedures, applicable requirements and equipment instructions; a quotation is not an operating plan.

Define submittals and acceptance evidence

Request a proposed one-line, elevations, connection details, device schedules, interlock descriptions and a clear list of exceptions for review before fabrication. The design team should compare them with the interface inventory and update the protection study as needed. Clarify whether control schematics, communications point lists and operating instructions are included.

Specify factory inspection and functional testing objectives, witness requirements, acceptance criteria and the records needed at turnover. Separately assign field testing, relay settings, utility coordination and final commissioning. Select applicable equipment standards by assembly type; if a low-voltage switchboard alternative is considered, verify any required UL 891 listing for that specific assembly rather than assuming it applies to the switchgear.

Compare proposals on scope and schedule

A useful purchase request includes the verified interface package, environmental conditions, required delivery destination, desired milestones and review responsibilities. Ask the manufacturer to identify open engineering questions and any excluded work. If domestic component origin is a requirement, state it in the specification and obtain confirmation for the actual proposed components and their availability.

Compare proposals for switching devices, fault duties, enclosure construction, testing, documentation and shipping divisions, not just the total price. Drawing approval, component procurement, fabrication, inspection and site readiness all influence the schedule. Agree on change control and who owns each dependency so a design revision or delayed outage decision can be evaluated before it disrupts the project.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote