BUILT IN THE USA. READY FOR YOUR PROJECT.
Electrical Panelboards: Protection and Coordination
A panelboard distributes power to branch circuits, but its protective devices must also fit the upstream system.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A panelboard distributes power to branch circuits, but its protective devices must also fit the upstream system. An engineer reviewing a new assembly needs more than a circuit count: source fault current, feeder protection, connected loads and continuity priorities all affect the design. Owners and contractors can help by defining those interfaces before requesting a quotation.
Establish fault duty at the panel
The available short-circuit current at the panelboard depends on the source and the impedance between it and the panel. Provide the current one-line, utility fault information, transformer data and feeder conductor sizes and lengths. Motors or alternate sources may contribute fault current too; the engineer should evaluate credible operating configurations rather than assume one source controls every case.
The panelboard assembly must have a suitable short-circuit rating for the calculated duty, and protective devices must have appropriate interrupting ratings for their application. Continuous-current capacity is a different question: a panel sized for the load is not automatically adequate for a fault. Include the system voltage, phase and wire configuration so the review addresses the whole assembly.
Choose a protection approach deliberately
A fully rated approach uses devices with interrupting ratings suitable for the available fault current at their locations. A series-rated approach can sometimes use a specific tested or listed combination of an upstream protective device and downstream devices. The lower downstream rating is not a general permission to mix any breaker brands or types.
Ask the manufacturer to identify the exact combination, applicable ratings, marking and documentation for a proposed series-rated design. The engineer must also evaluate motor contribution and other conditions that can affect its acceptance. Compare the potential device cost with the constraints on future substitutions, upstream equipment selection and coordination before approving the choice.
Coordinate upstream and branch devices
Selective coordination aims to have the protective device nearest a fault operate without unnecessarily interrupting unaffected circuits upstream. A coordination study compares time-current characteristics across the relevant current range; two devices that coordinate at a modest fault level may not coordinate at a higher one. Where selective coordination is required, the engineer must check the applicable rules and specified extent.
Share upstream device types and settings, proposed panel main and branch devices, and both normal and alternate-source conditions with the study provider. Reducing clearing time for arc-flash risk can conflict with coordination objectives. Resolve that tradeoff through the project engineer and study, not by assuming that a particular setting or device guarantees both outcomes.
Match circuits to their loads
A branch schedule should identify circuit purpose, load characteristics, conductor information, number of poles and any dedicated equipment requirements. Motor starting, electronic loads and future circuits can influence device selection and the arrangement of spaces. A spare position is not the same as an installed spare breaker, and neither alone establishes capacity for future loads.
Where the design or applicable code calls for ground-fault or arc-fault protection, specify the required function and its location. Grounding and neutral arrangements must be coordinated with the protective scheme and source configuration. The engineer should verify device compatibility, panelboard listing and field termination provisions rather than assume interchangeable components.
Turn the study into a purchase package
For a direct-manufacturer quotation on a new assembly, provide the one-line, panel schedule, load and fault calculations if available, enclosure environment, cable entry and installation constraints. Identify the applicable specifications and listing requirements for the panelboard, then confirm the proposed assembly and its devices satisfy them. Ask for the assumptions and exclusions to be stated explicitly.
Submittals should make the panel rating, circuit arrangement, device identification, connection details and any series combination clear enough for engineering review. Assign responsibility for the coordination and arc-flash studies, final protective settings, field connections and acceptance testing. Compare quotations on those interfaces and documentation, not simply on the number of breaker spaces.
Schedule approvals and safe turnover
Allow time for the study provider to review actual device data and for the design team to resolve comments before releasing equipment for manufacture. Component availability, approved substitutions and drawing revisions can change the schedule. Track changes affecting fault duty or protection so the study and panel documentation remain aligned with the final design.
At handoff, retain approved drawings, device information, test records and the final study and settings as specified. Qualified personnel should perform installation, verification and any adjustments under applicable codes, site safety procedures and manufacturer instructions. The owner and contractor should coordinate outages and energization authorization; a purchase order does not replace that field planning.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT