BUILT IN THE USA. READY FOR YOUR PROJECT.
Electrical Switchboards: Protection and Coordination
A low-voltage switchboard distributes service or feeder power through a common bus and outgoing protective devices.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A low-voltage switchboard distributes service or feeder power through a common bus and outgoing protective devices. Choosing those devices is more than matching amperes to a load: the complete assembly must be suitable for the available fault duty, and its protective behavior must fit the rest of the electrical system. Early coordination between the purchaser, design engineer and manufacturer can prevent costly changes after drawings are approved.
Establish the fault duty at the board
Start with a current one-line diagram, system voltage and configuration, transformer ratings and impedance, conductor lengths, and utility fault-current information. Identify generators and significant motors that can contribute to a fault. The engineer should study both present and credible future source configurations; an available fault current at one location is not automatically valid at every feeder.
Compare calculated duty with the proposed switchboard assembly rating as well as each device’s interrupting rating. Assembly bus bracing and any relevant withstand duration must be consistent with the fault and its clearing time. Where needed, provide the source X/R ratio and other study assumptions so the equipment evaluation addresses the actual duty, not just a headline current value.
Choose protective devices as a system
A main circuit breaker can provide adjustable protection when its selected trip unit has the required functions; a fused main switch relies on its specified fuse characteristics. Feeder devices may also be breakers or fused switches. Compare interrupting capability, trip characteristics, physical space, maintenance implications and the available device options within the proposed assembly.
Fully rated devices are selected to meet their individual available interrupting duties. A series-rated combination can be an alternative only when the exact upstream and downstream devices, application conditions, labeling and applicable requirements support it. Do not assume a generic pairing qualifies: ask for the manufacturer’s documentation and have the design engineer review motor contribution and coordination limitations.
Define what coordination must achieve
Selective coordination aims to limit an interruption to the protective device nearest a fault, leaving unaffected feeders supplied. The engineer compares device time-current characteristics across the relevant current range and operating conditions. A drawing showing a main and several feeders does not by itself establish selectivity, especially where instantaneous trip regions overlap.
For example, a motor feeder must tolerate normal starting while still clearing faults, and its protection must be considered alongside the upstream main. Adjustable trip functions may offer useful flexibility, but an added delay can change equipment duty and incident energy. Specify the required coordination range and request study results or documented limitations rather than assuming complete selectivity.
Account for grounding and alternate sources
Ground-fault protection requirements depend on the service arrangement and applicable rules. Give the engineer the grounding configuration, neutral and bonding details, and any required sensors or trip interfaces. When multiple sources are present, the design must account for each operating state and the actual neutral arrangement; an incorrectly coordinated sensing scheme can compromise protection or cause unwanted trips.
Generator operation can produce different fault-current levels from utility operation, affecting both device sensitivity and coordination. Share the proposed transfer arrangement, source characteristics and operating sequences with the study provider. Protection settings also affect arc-flash results, so the responsible engineer should evaluate incident energy alongside reliability; a coordination objective alone does not establish safe working conditions.
Specify records and verification
The purchase specification should identify the required equipment standard and listing. UL 891 can be relevant to an appropriate switchboard assembly, but the purchaser should verify the proposed assembly’s actual listing and scope. Request a one-line, elevations, device schedule, rating information, connection details and identified exceptions for engineering review before fabrication commitments.
Separate the switchboard submittal from the project-wide short-circuit, coordination and arc-flash studies. Establish who supplies source data, performs each study, approves final settings and provides field test records. The final turnover package should reconcile installed device identities and settings with the approved study, include applicable instructions and document any revisions made during the project.
Connect the order to the project schedule
When requesting a quote for a new switchboard directly from a manufacturer, include feeder sizes and destinations, load and motor data, required protection functions, site constraints and study responsibilities. Ask suppliers to identify assumptions and any alternate devices. A lower initial equipment cost may not be the better choice if a substitution weakens coordination or requires additional engineering review.
Sequence utility data collection, study development, submittal approval, component procurement and factory testing so decisions arrive before they affect the build. Track changes to source capacity or feeder loads through the study and drawings. Qualified electrical personnel should handle installation, testing and settings under the site safety plan, applicable requirements and manufacturer instructions; energization requires the owner’s designated authorization.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT