BUILT IN THE USA. READY FOR YOUR PROJECT.
Medium-Voltage Switchgear: Protection and Coordination
Medium-voltage switchgear must do more than carry the expected load: its switching and protective equipment must respond appropriately when the system is stressed or faulted.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Medium-voltage switchgear must do more than carry the expected load: its switching and protective equipment must respond appropriately when the system is stressed or faulted. For engineers, contractors, and owners, a useful purchase specification connects equipment duty with the protection study, utility requirements, and the facility’s tolerance for interruption. Those decisions belong together before the lineup is released for manufacture.
Establish the fault duty at the lineup
Begin with a current one-line diagram showing sources, transformers, buses, feeders, grounding, and operating configurations. Obtain the utility’s available fault information and assumptions, transformer impedance, conductor data, and contributions from generators and large motors. A study should consider credible maximum and minimum fault levels, including different source and tie configurations, rather than treating one number as the whole system.
The engineer compares calculated duty with the proposed assembly and device ratings under the applicable standard. Continuous current, interrupting capability, closing or making capability, and short-time withstand are different requirements; the withstand duration matters. Fault-current asymmetry and the system X/R ratio can affect the evaluation. A higher-duty design may cost more or require a larger lineup, but understating the duty risks an unacceptable application.
Match the protective device to the circuit
A relay-controlled circuit breaker can provide adjustable protective functions and trip indication, while a fused switching arrangement may suit some transformer or feeder applications. The comparison must include voltage class, continuous load, available fault current, switching duty, device characteristics, and the intended maintenance strategy. A load-interrupter switch should not be assumed to interrupt fault current without a suitably rated protective device.
For a fused arrangement, review the fuse’s applicable interrupting and current-limiting characteristics, minimum interrupting capability where relevant, and coordination with transformer inrush and downstream protection. Breakers and relays offer settings flexibility, but add sensing, control-power, wiring, and testing interfaces. Ask the manufacturer to identify the proposed device arrangement, applicable standards, exceptions, and any choices still dependent on engineering review.
Coordinate protection for real operating scenarios
A coordination study compares time-current characteristics of the lineup’s protective devices with upstream utility protection and downstream feeder devices. The goal is for the protective device nearest a fault to clear it when practical, while another device provides backup. The study also checks transformer damage limits, magnetizing inrush, motor starting, and applicable conductor or equipment withstand constraints.
Selective operation may not be achievable at every fault level or in every source configuration. For example, a feeder setting that coordinates with an upstream device in normal operation may need review when a generator supplies the bus. Faster clearing can reduce incident energy in some cases, but it can also narrow coordination margins. The study engineer should document those tradeoffs and any unresolved utility interfaces.
Define sensing, trip power, and control interfaces
Current transformers must have suitable ratios and protection performance for the intended fault range, connected burden, and relay functions. Voltage transformers, where required, need compatible ratings and interfaces for metering or directional protection. Ground-fault sensing depends on the system grounding arrangement and the selected scheme; provide neutral and grounding details rather than assuming a generic sensor configuration.
Specify the trip and control power source, supply voltage, monitoring expectations, and behavior if that supply is lost. Clarify who provides any battery system, communications network, and remote indication. Relay inputs, trip outputs, breaker auxiliary contacts, interlocks, and alarm points need an agreed interface list so the protective scheme remains coherent across equipment and facility controls.
Put study obligations into the purchase scope
Request a proposal identifying the applicable equipment standard and edition, rated characteristics, relay and sensor selections, one-line, elevations, wiring diagrams, and device schedules. State whether a particular listing or third-party evaluation is required and verify its applicability to the actual assembly. The direct manufacturer of new equipment and the project engineer should reconcile proposed components with the specification before approval.
Assign responsibility for the short-circuit, coordination, and arc-flash studies separately from fabrication. The study provider needs final device types, relay curves, transformer and sensor data, and upstream protective information; the manufacturer needs approved settings and interface requirements at the agreed point. Identify who supplies settings files, reports, labels if required, and final as-built drawings.
Schedule approvals, testing, and turnover
Build the schedule around utility data, submittal review, long-lead component confirmation, study revisions, manufacturing, and the agreed test program. Changes to source capacity or protective devices after approval can affect duty calculations and coordination, so record revisions and notify the parties responsible for the studies. Compare quotes for scope and assumptions, not just the number of sections.
Define factory checks and field commissioning separately, including relay configuration verification, applicable injection and trip-circuit tests, functional checks, and documented acceptance criteria. Agree on witness requirements and who resolves discrepancies. Qualified electrical personnel must perform testing and energization under the site’s safety procedures; the owner should receive approved settings, test records, operating instructions, and updated drawings for ongoing maintenance planning.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT