BUILT IN THE USA. READY FOR YOUR PROJECT.
Medium-Voltage Switchgear: One-Line and Feeder Planning
A medium-voltage one-line diagram is more than a picture of breakers and buses.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A medium-voltage one-line diagram is more than a picture of breakers and buses. It is the starting point for deciding how a new switchgear assembly receives power, serves individual feeders, and accommodates later changes. Owners, engineers, and contractors can use it to clarify equipment boundaries before requesting a quotation and to expose design questions that otherwise surface during fabrication or installation.
Trace every source and operating state
Show each utility supply, transformer, generator, and potential tie that can contribute power to the lineup. Identify normal and alternate arrangements, including whether sources may ever operate in parallel. A main-tie-main arrangement, for example, can support operational flexibility, but it also introduces protection and interlocking decisions that a single-source lineup may not need.
Provide the system nominal voltage, frequency, phase configuration, grounding method, and available fault information at the proposed connection. The engineer should request utility data and account for contributions from other sources under the relevant operating states. Maximum and minimum fault conditions both matter: equipment duty and protective sensitivity are different checks.
Turn feeder destinations into equipment requirements
Label each outgoing circuit by its destination, such as a transformer, motor controller, or distribution substation. A feeder schedule should distinguish present demand from connected load and identify planned operating conditions. Transformer characteristics, large motor starting, and feeder length can affect protection, voltage performance, and switching duty; they should not be reduced to a single ampere figure.
Assign a protective device and functional purpose to each circuit while the one-line is still being developed. A breaker-and-relay scheme can offer adjustable protection and monitoring, whereas a suitable fused switching arrangement may meet a simpler application. Compare fault duty, coordination, operating requirements, and serviceability rather than assuming either approach fits every medium-voltage feeder.
Resolve the cable and field connection interfaces
For each incoming and outgoing circuit, identify cable entry direction, conductor quantity and size, insulation and termination requirements, and the party furnishing the terminations. Cable bending space, pulling access, and the selected termination system can determine section dimensions. Coordinate phase arrangement, cable shields, grounding connections, and any current transformers with the engineer and installer.
A one-line cannot show all physical conflicts. Provide equipment-room or outdoor layout drawings, foundation information, route constraints, and desired front and rear access. The manufacturer can develop an arrangement for review, while the design team confirms applicable working clearances and the contractor verifies that the actual cable route and field connection details are feasible.
Define protection, control, and metering boundaries
The diagram should identify protective relays, current and voltage transformer locations, and metering points. Specify required measurements, transformer ratios and accuracy needs, and who supplies utility metering components. The protection engineer must evaluate instrument transformer suitability, available fault conditions, relay functions, and coordination with upstream and downstream devices before final settings are established.
Identify the control power source, trip supply, alarm and status contacts, remote-control expectations, and communications protocol. For multiple sources, document permitted operating states and required interlocks rather than leaving their intent to inference. Agree on a point list, wiring interfaces, loss-of-control-power behavior, and responsibility for integrating and testing external controls.
Make future capacity a defined choice
A future feeder shown as a dashed line is useful only if its expected load, timing, and connection concept are also recorded. Compare an installed spare protective device with an equipped spare section or an allowance for a later lineup extension. Each choice carries different initial cost, footprint, outage implications, and component availability.
Reserved physical space alone does not establish electrical capacity. The engineer should evaluate bus and source loading, short-circuit duty, protection coordination, and termination space for both present and credible future conditions. Ask the manufacturer to identify what is included now and what would require later engineering and approval; never assume an expansion can be added unchanged.
Translate the diagram into an actionable purchase
Send the manufacturer the current one-line, feeder and load schedules, fault and grounding data, site layout, environmental conditions, applicable project standards, and required documentation. State whether metal-clad or another construction is specified and ask for confirmation of the proposed assembly and ratings. Compare quotations against the same scope, including exclusions, testing, shipping splits, and field interfaces.
Plan time for drawing review, utility or owner approvals, component procurement, factory testing, delivery, and field commissioning; changes to source or feeder data can affect each stage. Request final drawings, device information, test records, and installation documentation as agreed in the order. Qualified electrical personnel and the responsible engineer must direct field work, protection settings, and energization under site safety procedures.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT