AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Circuit Breaker Trip Units

A circuit breaker trip unit determines how a breaker responds to abnormal current; its capabilities can shape both equipment protection and continuity of service.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Rows of gray electrical switchgear cabinets in a spacious industrial room.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A circuit breaker trip unit determines how a breaker responds to abnormal current; its capabilities can shape both equipment protection and continuity of service. Specifying engineers, contractors and facility owners should choose functions with the power system in view, not simply request an adjustable breaker. The useful choice depends on the loads, available fault current, adjacent protective devices and the study that will establish final settings.

Choose the protection approach

Thermal-magnetic breakers generally use thermal response for sustained overcurrent and magnetic response for higher short-circuit current. Electronic trip units use current sensing and electronic processing and may offer a wider selection of adjustable protection functions, event information or communications. Actual features and adjustment ranges depend on the specific breaker and trip unit, so compare published curves and documentation rather than assuming equivalent performance.

A separate protective relay and breaker arrangement may suit some applications, particularly where a more extensive protection scheme is needed. It introduces additional interfaces such as instrument transformers, trip circuits and control power. The design team should confirm the proposed device fits the assembly, is appropriate for the system duty and satisfies the project specification before treating either approach as interchangeable.

Understand functions and settings

Long-time protection addresses sustained overcurrent, while short-time and instantaneous functions respond to higher currents on different time scales. Some electronic units add ground-fault protection. A unit described as LSI or LSIG indicates a family of functions, not a promise that every pickup and delay can be adjusted over the range a particular study requires.

Review the breaker frame, sensor or rating plug where applicable, and the available setting increments together. A nominal breaker current does not by itself tell the engineer the actual long-time pickup. Ground-fault sensing also depends on the system grounding and sensor arrangement; the designer must establish whether the chosen scheme needs a neutral sensor and how it interfaces with the assembly.

Coordinate without losing sight of fault energy

A coordination study compares time-current characteristics of upstream and downstream devices over the relevant current range. Selectivity aims to disconnect the faulted portion while leaving other loads energized, but an apparent separation on one plot is not proof of coordination at every fault level. The study should account for device tolerances, instantaneous behavior and any manufacturer-published coordination limits or tested combinations.

Longer delays can improve selectivity in some cases but may increase incident energy or expose equipment to fault current for longer. The engineer must check protection and equipment withstand alongside the arc-flash study rather than optimizing a curve in isolation. Zone-selective interlocking can be considered where compatible devices and a verified wiring scheme support it; its behavior must be evaluated for each operating mode.

Give the study team usable system data

Start with a current one-line diagram showing sources, transformers, buses, main and feeder breakers, conductors and downstream devices. Supply system voltage, phase and wire configuration, grounding method, equipment ratings and utility fault information. Include conductor lengths and sizes, transformer impedance, existing device curves and proposed trip-unit ranges so the study is based on the actual distribution path.

Describe normal and alternate source arrangements, including generator operation, ties and any planned expansion. Minimum as well as maximum fault conditions matter because source impedance and operating configuration can change current at a protective device. Load schedules, motor starting and transformer inrush information help the engineer distinguish expected temporary current from conditions that require a protective response.

Define sensing, controls and data interfaces

Specify the desired metering, alarms and event records separately from the protective functions. If the unit communicates with a building system, identify the required protocol, physical connection, point list, network boundary and responsibility for configuration. Confirm whether protection depends on auxiliary power for the selected device, and document behavior on loss of that power rather than assuming all units behave alike.

Neutral or external sensors, trip actuators, interlocking connections and auxiliary contacts need clear ownership and wiring details. A communications link is not a substitute for the engineered trip path. Request drawings that identify terminal points and the supply boundaries between the manufacturer, installation contractor and other vendors; confirm compatible components and any project-specific listing requirements for the complete assembly.

Purchase, review and hand off the settings

For a new switchgear or distribution assembly, ask the direct manufacturer to identify the proposed breaker and trip-unit functions, adjustable ranges, sensing components, communication options and exceptions. Compare quotations against the same one-line, fault duty and documentation scope. Obtain time-current curves, device data and submittal drawings for engineering review; do not infer assembly suitability from a trip-unit description alone.

Schedule coordination-study inputs and device approvals early enough to inform purchasing, while allowing for revised source data and final settings. Assign a qualified study provider to issue an approved settings schedule and identify who programs, tests and records those settings. Qualified personnel should complete field work under site safety procedures and manufacturer instructions, with test results, final drawings and settings included in the owner’s turnover package.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote