AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Multiple Power Sources and Interlocks

A switchgear lineup fed by more than one power source needs more than a second incoming breaker.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Gray switchgear cabinets with red circuit-line markings on wooden pallets.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A switchgear lineup fed by more than one power source needs more than a second incoming breaker. Its design must define which sources can reach each bus, when a connection is allowed, and what happens when a signal or device fails. Specifying engineers, contractors, and owners should settle these questions before purchasing an assembly or scheduling an outage.

Map every path to an energized bus

Start with an up-to-date one-line diagram showing utility services, transformers, generators, energy storage, solar inverters, UPS connections, and any feeder that could backfeed the lineup. Mark normally open ties and alternate connection points. A source outside the new equipment scope can still energize its bus or affect the interlock design.

For each source, identify its owner, available capacity, protection, grounding arrangement, and control interface. Show the loads that must remain supplied and those that can be shed. For example, a generator may support essential feeders but not the entire facility, making load priorities as important as the source-transfer hardware.

Decide whether sources may ever parallel

Unintended paralleling can occur when two energized sources are connected through a common bus or tie without the required design and authorization. In a main-tie-main arrangement, a state table might prohibit both mains and the tie from being closed together. The engineering team should also consider backfeed through downstream connections, not just the three visible breakers.

An open-transition scheme separates sources during transfer, accepting a brief interruption. A deliberately engineered closed-transition scheme can reduce that interruption but requires appropriate synchronization, protection, controls, and any necessary utility authorization. Specify the permitted parallel duration and conditions rather than assuming that a synchronism check alone makes the scheme acceptable.

Select interlocks for the actual devices

Mechanical interlocks physically constrain device combinations or access; key interlocks can enforce a defined exchange between locations. Electrical interlocks use device status and control logic to block a command when its permissives are absent. Their suitability depends on breaker construction, separation between devices, and the operating sequence, not simply the number of sources.

Mechanical arrangements add hardware and can limit layout flexibility. Electrical logic can support more complex sequences and remote indications, but relies on correctly wired, available control power and trustworthy position feedback. Where both are specified, document how they interact. Neither an interlock nor a remote indication replaces the site’s qualified-person isolation and verification procedures.

Turn operating philosophy into a state matrix

Describe normal supply, source failure, transfer, restoration, and maintenance configurations in an agreed matrix. For each state, record required breaker positions, source-availability signals, permitted commands, alarms, and the responsible operator or controller. Include how manual, automatic, and remote authority are selected so conflicting commands cannot be treated as a normal operating condition.

Specify responses to lost control power, failed communications, inconsistent auxiliary contacts, and a breaker that does not reach its commanded position. Define time delays and inhibit or alarm behavior in the project sequence. The manufacturer and design engineer should resolve ambiguous states before drawings are approved, rather than leaving assumptions for the field team.

Coordinate protection and external interfaces

Each permitted source combination can change available fault current and the direction of fault contribution. The engineer should evaluate device interrupting duty, assembly withstand, protective settings, and coordination for applicable configurations. Generator and inverter fault behavior can differ from utility behavior; source data and study assumptions should reflect the actual equipment and operating modes.

Clarify whether neutral switching is required by the grounding design and applicable rules, and coordinate it with transfer equipment. Provide terminal schedules for generator start, source status, trip, alarms, and any supervisory system. Identify signal voltage, contact type, control-power ownership, and the boundary between the new assembly and equipment supplied by others.

Buy against a verifiable sequence

A useful request for a new assembly includes the one-line, source and fault data, load priorities, state matrix, required device functions, physical constraints, and applicable project standards. Ask the direct manufacturer serving San Antonio, South Texas, and nationwide to identify proposed devices, interlocks, exclusions, testing, and documentation. For a specified switchboard, verify any required UL 891 listing and its project-specific scope.

Request drawings, interlock and control schematics, a point list, operating-state documentation, and agreed factory functional test results. Define who supplies field wiring, settings, utility coordination, and site commissioning. Allow schedule time for source-data collection, approval comments, component procurement, and witnessed tests if required. Qualified electrical personnel must handle installation, testing, and energization under the project’s safety procedures.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote