BUILT IN THE USA. READY FOR YOUR PROJECT.
Surge Protection for Switchgear
A surge protective device (SPD) can limit transient overvoltage reaching distribution equipment, but its value depends on where and how it is connected.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A surge protective device (SPD) can limit transient overvoltage reaching distribution equipment, but its value depends on where and how it is connected. For engineers, contractors and facility owners, the purchasing decision is not simply a large surge-current number. Specify the system, connection arrangement, protection, monitoring and maintenance provisions together so a new switchgear assembly fits the actual project.
Decide where protection belongs
Start with the one-line diagram and identify the service, distribution buses and particularly sensitive loads. An SPD at the service can address transients entering there; downstream devices may also be appropriate where long feeder runs or locally switched loads create different exposure. No single location guarantees protection of every connected device.
Device type and location must be compatible. A Type 1 SPD may be considered on the supply side of the service disconnect when its listing, applicable requirements and utility allow it; a Type 2 is intended for the load side. Point-of-use protection can supplement an upstream device, subject to its own installation requirements.
Match ratings to the electrical system
Provide the nominal system voltage, phase and wire configuration, grounding arrangement and available fault current at the proposed connection. A four-wire wye system and a delta system can require different SPD configurations. Identify unusual conditions, such as a high-leg or resistance-grounded system, rather than assuming a device for one configuration suits another.
The specifying engineer should review the maximum continuous operating voltage for each protection mode, the voltage protection rating, and the short-circuit ratings of both the SPD and assembly against project conditions. Nominal discharge current and surge-current capacity describe different aspects of performance; neither substitutes for checking voltage compatibility, connection modes or fault duty.
Account for leads and physical layout
Even a well-rated SPD has to reach the bus through conductors whose impedance can add to the transient voltage seen by equipment. The layout therefore matters: ask the manufacturer to show the device location, connection points and proposed conductor routing. Short, direct routing with minimal loops is an engineering objective, not a substitute for the device instructions.
An internally mounted unit can reduce connection distance and simplify a coordinated enclosure layout, but it consumes space and must fit the assembly design. An externally mounted unit may provide easier separate access, while requiring coordinated mounting, wiring and enclosure protection. Evaluate either option against the actual room, cable paths and approved equipment construction.
Coordinate disconnects and protection layers
Establish whether the SPD requires a dedicated overcurrent protective device or disconnect, and who supplies it. Select and locate these provisions according to the SPD instructions, assembly design and applicable requirements. Consider the consequences of an SPD fault or protective device opening: a monitoring signal should make loss of protection visible without assuming the main remains unaffected.
For facilities with multiple stages, ask the design engineer and device suppliers to review coordination between service, downstream distribution and point-of-use protection. Cascading devices does not automatically produce a predictable protective level. Surge protection also does not replace grounding and bonding, lightning protection, or an analysis of sustained or temporary overvoltage conditions.
Make status and access usable
An SPD can degrade or disconnect after exposure to transients. Specify whether local status indication, a remote alarm contact or building-management monitoring is needed, and define the signal, destination and responsibility for field wiring. An alarm is useful only if someone is assigned to respond and the loss-of-protection condition is understood.
Ask how status can be checked and how a failed module or complete device would be replaced under the approved maintenance plan. Show access space and any barriers on the drawings. Inspection, isolation and replacement belong to qualified personnel following site safety procedures and manufacturer instructions; indicator visibility does not make exposed electrical parts safe to approach.
Request a complete submittal and handoff
For a quotation from a direct manufacturer of new distribution assemblies, send the one-line, system data, fault study information, enclosure environment and preferred SPD location. Identify requested protective modes, ratings, listing requirements and monitoring interfaces. Where specified, request evidence of the SPD's UL 1449 listing or component recognition, as applicable, and confirm that its integration is covered by the assembly's applicable evaluation.
Before fabrication, coordinate the equipment drawings, device documentation, connection details, alarm point list and responsibilities for field wiring and commissioning. Agree on the review sequence and dates for missing utility or study data; later changes can affect layout, component selection and schedule. At turnover, retain final drawings and SPD instructions with the facility maintenance records.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT