BUILT IN THE USA. READY FOR YOUR PROJECT.
Arc-Flash Risk Reduction
Reducing arc-flash risk starts with decisions about the electrical system and the work people must perform around it.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Reducing arc-flash risk starts with decisions about the electrical system and the work people must perform around it. New switchgear can incorporate protective and operating features, but no feature removes every hazard. Specifying engineers, contractors and facility owners should compare the effect of each measure on exposure, fault clearing, continuity and the way the equipment will be maintained.
Start with the work and the system
An arc-flash study estimates incident energy and boundaries for defined system conditions; it is not a guarantee of personal safety. A qualified study provider needs the current one-line, source and transformer data, available fault current, conductor information, protective device characteristics and operating configurations. Include generator contributions and tie states where applicable, because different source combinations can change the result.
The owner should identify tasks that require interaction with the lineup, their frequency and where personnel would stand. De-energized work, established through a qualified-person process under applicable safety rules, is generally the preferred way to reduce electrical exposure. A study label supports planning but does not replace task-specific risk assessment or safe work practices.
Balance clearing speed and coordination
A protective device can limit the duration of an arcing event when it detects and clears the fault promptly. The engineer should evaluate the actual arcing-current range and device time-current characteristics rather than assume the lowest setting always yields the desired result. Some conditions may fall outside the intended instantaneous response, so each relevant operating case deserves review.
Faster clearing may conflict with selective coordination: an upstream device could interrupt more loads than a downstream fault requires. Zone-selective interlocking or other coordinated protection functions may offer an alternative where the equipment and study support them. Specify the intended logic, compatible devices and study responsibility rather than purchasing the feature by name alone.
Evaluate special protection functions
A maintenance setting can temporarily change protective response for an approved work condition, but its benefit depends on the fault location, available current and device arrangement. It can also change selectivity and increase nuisance interruption risk. The project should define authorization, status indication, control ownership and how the normal configuration is restored and verified under site procedures.
An arc-detection scheme may use light sensing with a current or other supervised condition to initiate a protective response. Its effectiveness depends on sensor coverage, control power, trip paths and which breaker can clear each source. The designer should examine faults on the supply side as well as downstream; a device cannot clear a source it does not interrupt.
Specify remote operation with context
Remote switching can reduce the time a person spends near equipment during certain operations. It does not reduce the energy released by an internal fault by itself, and distance alone does not make an operation safe. The owner and engineer should assess the specific task, location, arc-flash boundary and applicable operating procedures before selecting a remote station.
Define the local and remote control authority, indications, permissives, communications interface and response to loss of control power. Identify whether operating devices are hardwired or networked, who supplies the external wiring, and which functions will be tested. Controls and displays should make equipment status understandable without implying that indication substitutes for required verification.
Design for inspection and maintenance
Access, compartment layout and isolation provisions influence how readily qualified personnel can maintain protective devices and connections. Drawout construction or barriers may support a maintenance strategy where appropriate, but neither automatically establishes an electrically safe work condition. Compare the added space and cost with the owner’s outage constraints and the actual tasks anticipated.
Protective equipment relies on a documented inspection and maintenance program. The owner should assign responsibility for condition assessment, testing and settings management using manufacturer instructions and applicable site rules. Reduced performance or changed system conditions can invalidate study assumptions; review settings and risk assessments when modifications or operating configurations change.
Turn the risk strategy into an order
When requesting a quote for newly manufactured equipment, provide the one-line and study assumptions, intended operating modes, required protective functions, available fault data and desired maintenance features. Identify control power, remote station location, sensing and trip interfaces, and any project-specific component sourcing requirements. The direct manufacturer can review the proposed assembly scope and confirm availability and applicable listings.
Request drawings showing device arrangement, control connections and interfaces, plus a functional test plan and documentation of approved settings responsibilities. Schedule study updates and design review before releasing final settings and control logic; coordinate factory checks, field commissioning and owner acceptance separately. The engineer, manufacturer, contractor and owner should resolve open interfaces without assuming one party performs every task.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT