BUILT IN THE USA. READY FOR YOUR PROJECT.
5 kV Switchgear
A 5 kV switchgear specification starts a design conversation; it does not by itself establish the correct equipment class or protection.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A 5 kV switchgear specification starts a design conversation; it does not by itself establish the correct equipment class or protection. A facility may use medium-voltage distribution to feed transformers, motors or campus circuits. The engineer must reconcile actual system characteristics with the assembly and devices before a contractor or owner can compare proposals for newly manufactured equipment.
From system voltage to equipment class
Identify the nominal line-to-line voltage, frequency, phase arrangement and maximum expected operating voltage on the one-line diagram. A 4.16 kV nominal system, for example, may be associated with a 5 kV equipment class, but that shorthand is not an approval. The engineer must check the proposed assembly and every connected device against actual system conditions.
Voltage selection also involves insulation requirements and anticipated transient overvoltages, not just steady-state voltage. Specify the required insulation level and applicable equipment standard, then ask the manufacturer to identify the ratings offered for the proposed construction. Surge protection and insulation coordination should be addressed by the design team in the context of the source, cables and connected loads.
Match protection to the source and loads
Provide available fault-current information at the proposed lineup, including utility contribution and relevant transformer, generator and motor data. The selected interrupting devices must be suitable for the available duty; bus and assembly withstand capabilities must also be checked against the fault magnitude and clearing time. A continuous-current figure alone says nothing about those fault duties.
For each feeder, describe its load, protective functions, current-transformer needs and control interface. A motor feeder and a transformer feeder can require different protection and coordination considerations. Identify who prepares the short-circuit and coordination studies, establishes relay settings and performs field testing; the equipment proposal should not be mistaken for a completed system study.
Choose construction around access and exposure
Discuss whether the specification calls for metal-clad or metal-enclosed construction and what compartmentation, switching devices and access provisions are required. These descriptions are not interchangeable. Drawout devices may support a particular maintenance philosophy, while fixed construction may offer a different footprint and cost profile; feasibility depends on the selected assembly and its verified ratings.
State whether the lineup will be indoors or outdoors, along with ambient temperature, altitude, humidity, contamination and corrosion concerns. Condensation control, ventilation and enclosure selection influence insulation performance and operating conditions. The designer should review equipment clearances, heat rejection, room access and any environmental derating with the manufacturer rather than assume a standard arrangement fits.
Define the cable and control boundaries
A useful feeder schedule identifies cable sizes and quantities, entry direction, termination type, shield grounding requirements and available bending space. Coordinate termination compartments and access with the cable supplier and installing contractor. For transformer or bus connections, provide connection elevations, phase arrangement and physical tolerances so a workable interface can be reviewed before fabrication.
Control power, relay inputs, trip circuits, indications and communication points need equally clear ownership. Specify the source and voltage of control power, any battery interface, network protocol and required remote signals. If a utility or another equipment supplier is involved, assign responsibility for drawings, interface approvals and integrated functional checks.
Compare quotations and submittals
Send the direct manufacturer a current one-line, load and feeder schedules, fault-duty information, site constraints and the required project standards. Include the intended in-service date, review milestones and any future feeder provisions. For work in San Antonio, South Texas or elsewhere nationwide, the same information allows the equipment scope to be evaluated without assuming a particular local facility.
Compare proposals by device duties, enclosure and construction, included controls, test scope, documentation and exceptions rather than by voltage label alone. Request drawings showing elevations, one-line details, terminal interfaces and equipment ratings. Confirm the applicable certification or listing, if specified, for the actual assembly; a low-voltage switchboard listing should not be assumed to cover medium-voltage switchgear.
Plan the path from approval to energization
Agree on the sequence for design review, component availability checks, fabrication, factory inspection and shipment. Release dates depend on approved drawings and procurement decisions, so track open questions and changes explicitly. Define factory test criteria and records, shipping splits, weights and lifting information, as well as who supplies the foundation, field cables and connections.
The owner and contractor should coordinate delivery access, installation, outage windows and commissioning with the utility and other affected parties. Qualified personnel perform electrical work and verify readiness under site procedures, applicable codes and equipment instructions. Turnover should include approved drawings, test reports, manuals and final settings documentation, with responsibilities for unresolved items clearly assigned.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT