BUILT IN THE USA. READY FOR YOUR PROJECT.
Metal-Clad Switchgear for Oil and Gas
Oil and gas facilities depend on medium-voltage distribution to serve substantial process loads, but a refinery, gathering installation and processing plant may have very different electrical and environmental constraints.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Oil and gas facilities depend on medium-voltage distribution to serve substantial process loads, but a refinery, gathering installation and processing plant may have very different electrical and environmental constraints. Metal-clad switchgear can provide a compartmented arrangement for critical feeders when its construction, protection and location are engineered for the actual facility. Owners and specifiers should settle those interfaces before comparing proposals.
Decide where compartmentation earns its space
Metal-clad construction separates major components into grounded metal compartments under the applicable equipment standard. A drawout circuit breaker arrangement and shutters at primary disconnects can support planned maintenance and separation of components. Confirm the proposed construction and applicable standard with the manufacturer; a metal enclosure alone does not establish that a lineup is metal-clad.
That separation does not eliminate electrical hazards or make energized access automatically safe. A process owner may value maintainability enough to accept a larger footprint and more complex equipment than a simpler arrangement. Compare that benefit against the plant’s outage tolerance, room dimensions and maintenance practices rather than selecting by name alone.
Build the lineup around process motor duty
Provide a one-line diagram and a load schedule showing the source, transformers, motor feeders and future connections. For large pumps, compressors and other motors, include running current, starting method, starting frequency, acceleration requirements and allowable voltage dip. Multiple motors starting close together can affect both source capacity and the operating process.
Define the boundary between the switchgear feeder and any separate motor starter, drive or control package. A variable-frequency drive introduces its own input, harmonic and protection questions; its supplier and the project engineer should coordinate these with the distribution design. Reserve spare feeder positions only after checking bus capacity, physical space and planned growth.
Coordinate protection with all operating states
The design team needs normal and alternate source configurations, system grounding, available short-circuit current and the relevant motor contribution. Equipment voltage class, continuous current, interrupting capability and short-time withstand must be evaluated together for the intended duty. A feeder’s normal load alone is not enough to establish its protective-device or assembly requirements.
Specify the required relay functions, current transformer characteristics, trip power source and signals to plant controls. An engineer’s protection and coordination study should consider both maximum and minimum fault conditions, upstream devices and downstream motor protection. Identify who supplies relay settings, reviews interlocks and verifies alarm, trip and status interfaces during commissioning.
Resolve classification and site exposure early
Oil and gas service does not by itself establish a hazardous location. The responsible classification team should define applicable area boundaries, gas or vapor characteristics and temperature requirements, then determine whether the equipment location is acceptable. A conventional metal-clad enclosure is not automatically suitable for a classified location; any special protection scheme requires project-specific review and approval.
Share expected ambient conditions, dust, humidity, rain, salt exposure and potentially corrosive gases. Indoor equipment still depends on the electrical room’s ventilation and condensation control; outdoor construction adds weather and access considerations. Evaluate coatings, heaters, ventilation and enclosure features as a coordinated design, including their effect on heat removal and maintenance.
Plan operator access and physical interfaces
Provide room plans, elevations and installation-route constraints, including door openings, floor loading and lifting limitations. Identify cable entry, conductor quantities and sizes, termination space and connections to transformers or bus duct. These details affect section widths, shipping splits and the work needed to join and install a lineup in the field.
Plan working clearances, breaker handling space and access to relays and cable compartments with the applicable code and manufacturer’s instructions in view. Remote indications or operating provisions may reduce the need for personnel to be near equipment during some tasks, but they do not replace a site-specific electrical safety and maintenance plan.
Purchase against defined deliverables and milestones
Request a proposal for a newly manufactured lineup from a direct American manufacturer serving San Antonio, South Texas and nationwide. Include the design basis, applicable standards, required testing and any component-origin requirements; confirm actual sourcing and availability. Ask for equipment elevations, one-lines, control schematics, a component schedule and a clear list of technical exceptions.
Agree on approval dates, component procurement dependencies, factory test scope and any witness requirements before fixing the project schedule. Define who handles delivery, foundations, field cabling, settings, site tests and energization authorization. Qualified electrical personnel must perform site work under approved procedures; final drawings, test records and manuals should be included in the turnover package.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT