BUILT IN THE USA. READY FOR YOUR PROJECT.
Low-Voltage Switchgear for Oil and Gas
Oil and gas facilities rely on low-voltage distribution to keep pumps, compressors and supporting systems supplied while controlling the consequences of electrical faults.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Oil and gas facilities rely on low-voltage distribution to keep pumps, compressors and supporting systems supplied while controlling the consequences of electrical faults. A new power circuit breaker switchgear lineup should reflect both the electrical system and the realities of the site. Owners and specifiers can obtain a more useful proposal by defining process priorities, area classification and access constraints before selecting a configuration.
Start with the process and its power sources
Provide an up-to-date one-line showing incoming sources, transformers, main and tie breakers, and downstream feeders. Identify operating modes, including generator supply or a normally open bus tie, and whether sources may ever operate in parallel. These choices affect fault duty, interlocking and protection; a drawing of the normal arrangement alone may conceal important design cases.
A load schedule should distinguish continuous process motors from intermittent pumps, utilities and future additions. Include motor starting method, expected starting frequency, and any drives or soft starters. The engineer can then assess starting voltage drop, heating and system capacity rather than selecting a bus solely from the sum of motor nameplates.
Coordinate motor feeders and protection
Power circuit breaker switchgear distributes and protects feeders; a separate motor control center or drive package may provide the individual motor control functions. Define where each assembly begins and ends, feeder termination responsibilities, and signals such as status and trip indication. That boundary makes it easier to compare proposals without omitting motor protection or controls.
Give the design team available fault-current data for each credible source arrangement and the protection study requirements. Breaker interrupting duty, assembly withstand and trip settings must be evaluated together. Selective coordination can limit an outage to the affected feeder, but achieving it depends on actual device curves, settings and fault levels, not simply choosing adjustable trip units.
Location and classified-area decisions
Send the site hazardous-area classification drawings and identify the proposed equipment location, including nearby ventilation openings and process equipment. The responsible engineer must determine whether the location and assembly are suitable under applicable requirements. An ordinary outdoor enclosure should not be assumed suitable for a classified location merely because it keeps out rain or dust.
Locating the lineup in a suitable electrical room may simplify access and environmental control, but can increase cable length and building requirements. An outdoor location can reduce some routing distances while exposing equipment and operators to weather. Evaluate any protected-room or pressurization scheme with the site engineer and authority having jurisdiction rather than assuming it removes classification constraints.
Design for exposure and service access
Describe ambient temperature, dust, moisture, solar exposure and any corrosive atmosphere, including potential hydrogen sulfide exposure where relevant. Ask the manufacturer to identify enclosure construction, finish, ventilation and condensation-control provisions proposed for those conditions. A more restrictive enclosure may affect heat rejection, so enclosure protection and equipment ratings must be reviewed as a system.
Share room dimensions, door and lifting routes, cable entry direction and available working space. Drawout breakers may support the maintenance strategy but require space and compatible handling provisions; fixed construction can have different access and outage implications. Required clearances and access arrangements depend on the actual installation and applicable rules, not a standard footprint assumed during purchasing.
Specify controls and operating boundaries
For a two-source arrangement, document permitted bus states, source-transfer philosophy and the interlocks intended to prevent unintended paralleling. Define control power, loss-of-control-power behavior and which indications or commands connect to the facility control system. Agree on communication protocol, point list and responsibility for network integration before the wiring and controls are finalized.
Operator access and remote indications can reduce unnecessary exposure, but they do not eliminate electrical hazards. The owner should assign qualified personnel to develop switching, isolation and maintenance procedures under site rules and manufacturer instructions. The project safety team should coordinate the protection study, arc-flash assessment and any required labeling with the final equipment data and settings.
Purchase against a complete scope
Request drawings showing the one-line, elevations, dimensions, feeder arrangement, terminations and control interfaces, plus device schedules and a list of exceptions. Specify the applicable equipment standard and any required independent listing; confirm the proposed assembly and its listing scope for the project. Ask who supplies field cabling, foundations, settings, installation, commissioning and final records.
A direct American manufacturer of new assemblies can work with teams in San Antonio, South Texas and nationwide using a common review package. Schedule time for drawing approval, component procurement, fabrication, agreed factory testing, shipping and site acceptance. For a planned changeover, the owner and contractor should align outage windows and contingency plans with the approved installation scope.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT