BUILT IN THE USA. READY FOR YOUR PROJECT.
Metal-Clad Switchgear: One-Line and Feeder Planning
A one-line diagram is the starting map for a new medium-voltage metal-clad switchgear assembly, but it cannot capture every design decision on its own.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A one-line diagram is the starting map for a new medium-voltage metal-clad switchgear assembly, but it cannot capture every design decision on its own. Owners, engineers, contractors and purchasing teams need to connect the drawing to actual sources, feeder loads, cable routes and future operating plans. That early coordination helps a manufacturer define compartment arrangements and identify open questions before equipment dimensions and interfaces are fixed.
Map sources and normal operating states
Show each incoming source, the point of connection, transformer characteristics and the normal state of main and tie breakers. Identify any alternate source and whether paralleling sources is permitted. A single bus can simplify the lineup, while a split bus and tie may offer operating flexibility at the cost of additional equipment, controls and space. Metal-clad construction separates major components with grounded metal barriers; the source and feeder arrangements affect compartment layout and the resulting footprint.
The engineer should supply system voltage and frequency, grounding method, available fault current and expected future source changes. Source contributions can change with operating configuration, so the design review should consider the relevant scenarios rather than one convenient snapshot. Equipment ratings and interrupting duties require project-specific verification; a diagram label alone does not establish suitability.
Turn feeder lines into usable equipment scope
Name each feeder destination and describe whether it supplies a transformer, motor, distribution lineup or another load. Provide anticipated demand, load characteristics and conductor information where known. A motor feeder may introduce starting and protection questions that differ from those of a transformer feeder, even if their one-line symbols appear equally simple.
Distinguish installed loads from planned additions and identify which loads must remain in service during a source change. The engineer can use that information to evaluate feeder and bus loading, protection and the proposed operating arrangement. Purchasing should flag uncertain loads explicitly rather than treating preliminary values as final ratings.
Coordinate cable and grounding interfaces
For every incoming and outgoing circuit, document the proposed cable quantity, conductor size and type, entry direction and termination responsibility. Cable bend space, termination hardware and access can affect compartment dimensions and lineup placement. Confirm whether cables arrive from a trench, below-floor space or overhead route before approving the arrangement.
The design team should also coordinate the equipment grounding connection, cable shields and any current transformers associated with ground-fault sensing. Termination details depend on the protection scheme and cable construction. The contractor and engineer should review the manufacturer’s connection drawings and available working space together, rather than assuming every feeder has the same interface.
Align protection, controls and metering
The one-line should identify protective devices and instrument transformer locations, but a complete request also defines protection functions, metering needs and ownership of the coordination study. Share upstream device data and downstream transformer or feeder information. Selectivity, sensitivity and equipment duty can pull in different directions, making coordination a project engineering decision.
Define control power sources, required alarms, remote indications and communication interfaces with the facility system. If automatic transfer or interlocking is contemplated, document the intended sequence and source conditions for review. Identify who provides settings, integration and field verification; an assembly drawing is not a substitute for a commissioned protection and control scheme.
Reserve expansion capacity deliberately
A spare feeder position, a provision for a future breaker and an extendable bus are different scopes. Compare their initial cost and footprint with the consequences of adding capacity later. A designated spare can reduce future interface uncertainty, but its actual equipment, protective functions and connection provisions should be stated in the quotation.
Ask the engineer to assess future loading, fault duty and physical extension routes, not merely the number of blank spaces on the drawing. Specify any required bus capacity and space for additional cables, controls and access. Future additions remain subject to a fresh engineering and equipment compatibility review, including applicable project requirements.
Purchase against a coordinated document package
Issue a current one-line with the equipment specification, available studies, site constraints and a feeder schedule. Request a scope breakdown, general arrangement, connection and control drawings, and a list of exceptions. Identify applicable standards, such as IEEE C37.20.2 where specified, project-specific listing requirements and factory test documentation in the purchase requirements. Verify what the proposed assembly actually covers.
Plan time for technical clarifications, drawing review, release, manufacturing, inspection and delivery coordination; confirm dates rather than assuming a fixed lead time. Assign responsibility for foundations, cable installation, settings and startup interfaces. Qualified electrical personnel must plan and perform installation, testing and energization under site procedures, applicable codes and manufacturer instructions.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT