BUILT IN THE USA. READY FOR YOUR PROJECT.
Metal-Clad Switchgear: Protection and Coordination
Protection planning for metal-clad medium-voltage switchgear starts with more than selecting a circuit breaker.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
Protection planning for metal-clad medium-voltage switchgear starts with more than selecting a circuit breaker. The lineup must fit the power system's fault duty, the protective scheme and the owner's operating priorities. For engineers, contractors and facility owners, a useful purchase specification connects the one-line diagram and coordination study to the physical compartments, relay wiring and commissioning responsibilities of a newly manufactured assembly.
Start with every source and operating state
Provide a current one-line showing utility connections, transformers, generators, motors, ties and outgoing feeders. Identify normal and credible alternate configurations, including whether sources can operate in parallel. Utility fault data and transformer impedances help the study engineer calculate duty at each bus; motors and local generation may contribute differently as a fault develops.
Ask the study provider to identify the highest and lowest relevant fault currents and the assumptions behind them. Maximum duty informs equipment selection, while lower fault levels can challenge protection sensitivity. If future sources or feeder changes are planned, distinguish confirmed design conditions from possible expansion so the quotation does not conceal an unverified assumption.
Match interruption and withstand to the study
The breaker must be suitable for the system voltage and the calculated interrupting duty under the applicable rating basis. The study and equipment teams should also review factors such as fault asymmetry and clearing time rather than comparing a single fault-current number to every device nameplate. Manufacturer engineering must confirm the actual proposed combination.
Bus and assembly short-time and momentary withstand capabilities are separate considerations from a breaker's interrupting capability. A deliberate coordination delay may require the equipment to withstand fault current longer, so the selected protective timing and assembly ratings must be reviewed together. Higher duty or longer withstand needs can affect construction, available choices and cost.
Define relay functions and sensing zones
Specify the protection functions needed for each main and feeder, based on the study and load characteristics. Overcurrent and ground-fault protection may be supplemented by directional or differential schemes where the system requires them. Transformer energization and motor starting can overlap protective curves, so sensitivity must be weighed against unnecessary trips.
Show current-transformer locations and ratios, protection accuracy, burden and saturation considerations on the relay design documents. Their location defines the boundaries of a protection zone. Voltage-transformer inputs, ground-sensing arrangements and relay functions must suit the actual grounding scheme and source configurations; the relay supplier and study engineer should resolve these interfaces together.
Coordinate clearing without assuming perfect selectivity
Coordination aims to remove the faulted portion while preserving unaffected loads where feasible. Time-current curves should compare feeder, main and upstream utility protection over the applicable current range and operating modes. Ask the study engineer to document settings, intentional margins and any regions where selective operation cannot be achieved.
Faster clearing may reduce incident energy in some conditions, while added delay can improve selectivity; neither result should be assumed without the project study. Metal barriers separate functional compartments, but compartmentation alone does not establish an arc-resistant rating or eliminate hazards. Evaluate any arc-energy reduction features against the specified construction, protection scheme and operating procedures.
Specify control power and compartment interfaces
Protection depends on a complete trip path, not just the relay. Define the trip supply, breaker coil requirements, monitoring, terminal interfaces and the response to loss of control power. Identify which party provides batteries, chargers or other external sources when required, and include alarm and status signals on the control drawings.
Relay devices, instrument transformers, cable terminations and breakers occupy different parts of a metal-clad lineup. Reserve the space and access needed for the specified components, wiring and testing arrangements. Agree on hardwired indications, communication protocol and point list where remote monitoring is required, and identify the boundary between manufacturer wiring and field connections.
Buy the complete engineering and test scope
Request a proposal that identifies the applicable project standards and required evidence of equipment ratings or listing, as appropriate. Compare breaker and relay functions, instrument transformers, drawings, factory checks and stated exceptions—not just the lineup size. Establish whether the coordination and arc-flash studies, relay settings and utility approvals are included or assigned separately.
Set milestones for source data, approved submittals, component release, factory testing and site commissioning, allowing for revisions and component availability. Deliverables should include approved one-lines, control schematics, device schedules and agreed test records, followed by updated turnover documentation. Qualified personnel must perform installation, protection testing and energization under site procedures and applicable requirements.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT