BUILT IN THE USA. READY FOR YOUR PROJECT.
27 kV Switchgear: Protection and Fault-Duty Review
A 27 kV designation starts a switchgear discussion; it does not establish that a particular assembly or protective device is suitable.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A 27 kV designation starts a switchgear discussion; it does not establish that a particular assembly or protective device is suitable. For a new distribution lineup, the owner, design engineer and manufacturer need a shared picture of operating voltage, fault sources and protection objectives. Engineering review must also confirm whether the requested construction and components are available for the application.
Define the system before choosing a voltage class
Identify whether 27 kV refers to the nominal system voltage or an equipment class in the project documents. Provide the actual source voltage, expected maximum operating voltage, frequency, phase arrangement and grounding method. The engineer can then evaluate the equipment's rated maximum voltage and insulation requirements against the system rather than treating the label as proof of compatibility.
Specify the required insulation level and any applicable equipment standards in the request for quotation. Altitude, contamination and the intended installation environment may affect the insulation design and equipment selection. The manufacturer should identify the proposed construction and any assumptions for the engineer to review; feasibility and actual ratings remain project-specific.
Establish fault duty at each operating state
A fault study starts with a current one-line diagram and source data, including utility fault contribution, transformer impedances and connections, feeder impedances and any generator or motor contributions. Show normal and credible alternate operating states, such as a tie closed or an alternate source connected. The highest duty may occur in a configuration that is not the usual operating arrangement.
Provide the study's available fault current and relevant X/R information at each proposed bus, together with the study assumptions and date. The manufacturer and engineer must compare the appropriate calculated duties with device interrupting and making duties and assembly withstand capabilities. Continuous-current capacity alone does not establish that the lineup can safely withstand or interrupt a fault.
Match clearing time to equipment withstand
Short-time withstand combines a current magnitude with a duration; it is not interchangeable with a breaker's interrupting rating. Relay operating time, breaker opening time and any intentional delay matter to the duty imposed on the assembly. Review the complete protection and switching arrangement against the applicable ratings and test basis, not just a single current figure.
Time delays can improve selectivity by allowing a downstream device to clear first, but they can also increase the duration of electrical stress and affect arc-flash exposure. The protection engineer should examine these competing objectives across the expected fault range, including the limits of each device's published curves and the specified assembly's withstand duration.
Coordinate relays, sensors and trip power
Provide the proposed protective functions and the utility or upstream coordination requirements. Overcurrent and ground-fault protection may need different sensing and settings depending on source grounding and fault levels. A coordination study should compare upstream and downstream characteristics for both normal and alternate source conditions, rather than assuming one settings set works for every configuration.
Document current transformer ratios, accuracy, burden and saturation considerations, along with voltage-sensing needs where applicable. Identify the relay inputs, breaker trip interface, control power source, alarms and behavior on loss of trip power. Clearly assign who supplies the study, approves settings, programs devices and verifies the trip circuit during commissioning.
Turn the protection design into a purchase scope
Include the one-line, load and feeder schedule, fault study, required protective functions, enclosure conditions and connection details in the inquiry. Describe incoming and outgoing cable arrangements and physical constraints so the proposed protection and insulation design fits the installation. Ask for an itemized quotation identifying devices, ratings, exclusions, applicable standards and exceptions.
Review proposed current transformers, relays, breaker interfaces and communications against the owner's control and monitoring system. Request submittal drawings showing the one-line, elevations, control schematics and terminal interfaces, plus project-specific rating and test documentation. If component origin is a purchasing requirement, state it explicitly and verify availability and sourcing rather than assuming every component qualifies.
Plan review, testing and the field handoff
Set milestones for utility data, fault and coordination studies, manufacturer submittals, approval, component procurement and factory testing. A change in source contribution or operating configuration can affect device selection and settings after the initial review, so track revisions and their schedule implications. Confirm the current schedule with the manufacturer instead of relying on a fixed lead-time assumption.
Agree on factory test scope, acceptance criteria and records before fabrication, and distinguish those checks from field acceptance and commissioning. The owner and qualified electrical personnel are responsible for site procedures, installation, verification and energization authorization under applicable requirements. Transfer approved drawings, settings, manuals and test reports to the team responsible for the finished system.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT