AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Switchgear Site Survey

A switchgear site survey turns the physical realities of a facility into usable design and purchasing information for a new distribution assembly.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Gray electrical switchgear cabinets with open doors on wooden pallets.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

A switchgear site survey turns the physical realities of a facility into usable design and purchasing information for a new distribution assembly. Engineers, contractors and owners can uncover conflicts between a proposed lineup, the building and existing circuits before drawings are approved. The survey supports, but does not replace, electrical design, code review or a qualified installation plan.

Set the survey boundaries

Begin with the latest one-line diagram, proposed scope and an owner contact who understands access restrictions. Agree which rooms, outdoor areas and delivery paths are in scope, and whether the survey is for an addition or a new replacement lineup. Mark missing drawings and unresolved dimensions instead of treating estimates as verified facts.

Coordinate the visit with the facility and electrical contractor around production, security and authorized access. Existing electrical equipment may present serious hazards even when a room appears quiet. Only qualified personnel working under the site safety program should assess energized equipment or obtain information requiring access beyond normal external observation.

Measure the room, not just the footprint

Record wall-to-wall dimensions, ceiling height and the positions of columns, pipes, ducts and doors. Note floor elevations, housekeeping pads and any uneven surfaces, using a consistent reference point. Photographs should be keyed to a sketch so a designer can tell which obstruction is above, beside or behind the proposed lineup.

A lineup that fits the available floor area can still conflict with working space, door swings or access for maintenance. The engineer and installer must verify applicable clearance and egress requirements for the actual equipment and installation. Reserve room for opening doors and handling components, not merely for placing the enclosure.

Trace cable and busway interfaces

Map existing conduit banks, cable trays, trenches and busway approaches against the intended top or bottom entry. Document available space, route changes and fixed obstructions; identify inaccessible portions as unverified. Conductor quantity and size, termination locations and bending space can change enclosure dimensions or require a different connection arrangement.

For a busway connection, record its orientation, elevation and support constraints, then coordinate the mating details with the busway supplier and design team. Clarify who provides field conductors, supports and terminations. A convenient entrance on paper may shift substantial routing or structural work to the contractor, affecting the full project cost.

Document the existing electrical interfaces

Where safely visible and permitted, photograph equipment identification plates, circuit labels and external connection locations. Compare those observations with the one-line, load schedules and known modifications. Labels and drawings can disagree, so flag discrepancies for the owner and engineer rather than assuming a feeder destination or available capacity.

The survey package should identify incoming sources, downstream feeders and any metering, controls or generator interfaces that the new assembly must accommodate. The engineer still needs project-specific system voltage, available fault current, protection and grounding information from responsible parties. Utility requirements and study updates may affect the final equipment specification.

Follow the delivery path to the final position

Check vehicle approach, unloading area, floor loading limits, door openings, ramps, turns, elevators and overhead restrictions along the entire route. Ask the rigging contractor and building representative to confirm usable dimensions and load limits. An opening that admits one shipping section may not provide room to turn or lift it safely.

Share the route constraints with the manufacturer before requesting a final layout. Shipping splits can make handling feasible, but add field alignment and connection work that must be assigned and scheduled. Compare provisional section sizes and weights with the plan, then reconfirm against approved drawings and the rigging contractor’s method.

Capture conditions and turn findings into a quote

Record indoor or outdoor exposure, ambient conditions, ventilation limitations, humidity, dust and corrosive sources where relevant. Note roof or plumbing leaks and the location of nearby heat-producing equipment. These observations help the design team evaluate enclosure and environmental needs; a room survey alone does not establish the assembly’s thermal performance.

Deliver a dated sketch, dimensioned photos, interface list and an open-items register identifying the owner of each answer. Send these with the one-line and desired testing and documentation scope to the manufacturer for a new-equipment quotation. Schedule review, utility input, fabrication and site work around resolved interfaces; track revisions when measurements or outage windows change.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote