BUILT IN THE USA. READY FOR YOUR PROJECT.
Electrical Switchboards for Data Centers
A data center switchboard distributes power to critical infrastructure, but its value depends on how it fits the entire electrical path.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A data center switchboard distributes power to critical infrastructure, but its value depends on how it fits the entire electrical path. Owners and specifying engineers must balance source redundancy, feeder protection, room constraints and the ability to maintain equipment without an unnecessary outage. A direct manufacturer can develop a new assembly around those project requirements when the operating scenarios and interfaces are defined early.
Define the source paths before the lineup
Begin with a one-line showing utility services, transformers, generators, transfer equipment, UPS systems and the switchboard feeders each source supports. Identify which loads require independent A and B paths and where those paths may share upstream equipment. Two incoming feeders alone do not establish redundancy if a common transformer or distribution section can interrupt both.
Where a main-tie-main arrangement is considered, describe normal and contingency states, allowable source combinations and the intended maintenance boundary. The engineer should establish interlocking and transfer requirements so the design does not permit unintended source paralleling. A tie can improve operating flexibility, but adds devices, space and coordination questions; it is not automatically appropriate for every architecture.
Size for growth and the loss of a source
Provide present and forecast load schedules by feeder, including UPS input, cooling, pumps, controls and other support loads. State whether growth means additional cabinets, higher rack densities or a future building phase. Evaluate demand in both normal operation and the credible contingency in which remaining sources and distribution paths must carry the transferred load.
Spare breaker positions provide connection flexibility, but unused space does not create bus, source or cooling capacity. Compare installed spares with prepared spaces or a planned extension, and verify the engineering and listing implications of later changes. Nonlinear electronic loads can affect neutral current and heating, so include neutral configuration and relevant power-quality assumptions in the review.
Coordinate protection with continuity
Supply available fault-current data at each source and operating state, transformer information and proposed upstream and downstream protective devices. The design team must assess the switchboard assembly short-circuit rating and individual device interrupting ratings against the applicable duty. Generator-supplied fault behavior may differ from utility-supplied behavior, affecting protection choices and study assumptions.
A coordination study compares protective-device characteristics so a feeder fault is less likely to disconnect unrelated loads. Complete selectivity across every condition should not be assumed: instantaneous protection, fault levels and arc-flash risk can create competing objectives. Record intended trip functions and settings responsibilities, and have qualified engineers resolve the tradeoffs for the actual system.
Meter what operations can act on
Decide whether the operations team needs source, main, tie or feeder measurements to track loading and identify a path approaching its limit. Specify quantities such as current, power, energy and demand, along with required accuracy, current-transformer ratios and any revenue-metering interfaces. Utility metering requirements should be coordinated separately from customer monitoring.
For integration with the data center management system, agree on communications protocol, point list, network boundary, time synchronization and responsibility for configuration. Identify control-power and loss-of-communications behavior as well. Metering supports capacity decisions and alarms, but it does not replace protective functions or prove that an alternate source can carry the load.
Make room for installation and maintenance
Share room dimensions, applicable working-space requirements, access routes, floor loading and top or bottom cable-entry preferences. Feeder quantity, conductor size and bending space can drive section width as much as bus capacity. Coordinate heat rejection with the mechanical engineer and identify ambient conditions rather than assuming the electrical room will always remain within equipment limits.
Discuss whether maintenance of a feeder or source section must leave other loads available, and compare that objective with the proposed barriers, isolation provisions and device construction. The qualified design team should verify that the actual arrangement supports the intended maintenance plan. Any shutdown and electrical work must follow site procedures and be performed by qualified personnel.
Buy against an agreed scope and schedule
Send the manufacturer the one-line, load and fault studies or available inputs, equipment specifications, room constraints, metering needs and anticipated in-service date. Ask proposals to identify assembly standards, device selections, exceptions and responsibilities for field connections, settings and commissioning. For an appropriate switchboard, verify any required UL 891 listing and its project-specific scope rather than assuming it.
Set review milestones for drawings, component approvals, fabrication and factory tests; late changes can affect both the design and schedule. Request elevations, connection details, protective-device schedules, test criteria and records, plus operating and maintenance documentation. The owner, contractor and commissioning team should agree on witness requirements, delivery access and coordinated outage windows before authorizing site work.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT