AMERICAN-BUILT POWER DISTRIBUTIONSAN ANTONIO & SOUTH TEXAS / NATIONWIDE SHIPPING

BUILT IN THE USA. READY FOR YOUR PROJECT.

Electrical Switchboards for Industrial Facilities

An industrial switchboard distributes power from a facility service or transformer to the feeders that support production.

DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

Switchgear cabinets loaded on a flatbed truck outdoors.
01 / POWER DISTRIBUTIONBUILT FOR THE JOB
Representative switchgear photography.
✦MADE IN THE USAAmerican components
▦UL 891Switchboards when specified
↗BUILT TO SPECProject-specific engineering
→NATIONWIDEShipping across the USA

THE MANUFACTURER’S PERSPECTIVE — 02

An industrial switchboard distributes power from a facility service or transformer to the feeders that support production. The right new assembly must fit more than the electrical room: motor starting, process continuity, fault protection and plant controls all shape its design. Owners and engineers can obtain a more useful direct-manufacturer proposal by describing the operating system and its physical interfaces before selecting devices.

Start with the plant load, not just the main rating

Provide a current one-line diagram and a feeder schedule showing source arrangement, system voltage, phase and wire configuration, present demand and planned loads. Identify which feeders supply motor control centers, drives, process equipment, lighting and other distribution. Show future capacity as a defined requirement rather than assuming that an empty compartment also provides sufficient bus capacity.

Large motors can impose starting currents and voltage dips that a running-load total will not reveal. Give the design engineer motor sizes, starting methods, expected starting sequence and process sensitivities. For variable-frequency drives, include input characteristics and any harmonic study requirements; the switchboard feeder supplies the drive, while motor control functions may reside downstream.

Match feeder protection to actual fault duty

Obtain available fault-current information at the proposed connection, including applicable utility, transformer and motor contributions. The engineer should evaluate the complete assembly short-circuit rating and the interrupting capability of each protective device against the calculated duty. A device rating alone does not establish the rating of every combination in a switchboard.

A coordination study can compare the main and feeder protective characteristics over the relevant fault-current range. Better selectivity may limit the loss of unrelated production loads, but settings, available devices and upstream constraints can impose tradeoffs. Identify who supplies device data, performs the study and approves settings; do not assume selective coordination is automatic.

Design around production interruptions

Map each critical process to its feeder and identify acceptable shutdown windows. Separate feeders may confine the impact of a downstream fault or maintenance event, while additional sections and protective devices consume space and add complexity. Where alternate sources are contemplated, define their capacity and the transfer arrangement rather than treating a second source as an automatic continuity solution.

Discuss access and isolation objectives during layout review. A switchboard does not by itself guarantee maintenance without an outage, and barriers or separate sections do not eliminate electrical hazards. The owner, engineer and qualified electrical contractor should define safe work practices, outage boundaries and any temporary-power plan under the site procedures and applicable requirements.

Coordinate motors, metering and controls

A switchboard usually distributes and protects feeders; a motor control center or drive system may provide the individual motor starting and control functions. Specify the boundary between these assemblies, including feeder destinations, conductor quantities, termination responsibilities and any required disconnect or protection. Coordinate inrush and drive characteristics with the equipment suppliers and study engineer.

For plant monitoring, decide which feeders need current, energy or power-quality data and how those measurements reach the facility system. Include meter functions, instrument transformer requirements, communication protocol, point list and network ownership. If remote indications or interlocks are required, document control power, normal and abnormal states, and who verifies the completed interface.

Fit the assembly to the industrial environment

Share equipment-room dimensions, access routes, cable entry direction, conduit quantities and working-space constraints. Heat from the switchboard and nearby drives affects room ventilation; dust, moisture, washdown or corrosive conditions may influence enclosure selection. An outdoor location also needs coordination with civil design, exposure and access. Confirm the specific enclosure and thermal design for the site.

Compare the proposed lineup footprint and shipping sections with doors, handling equipment and the installation route. Clarify who supplies foundations, anchorage, field conductors and any connections between shipped sections. For service equipment, coordinate metering, service disconnect arrangements and applicable utility and authority requirements before releasing drawings for fabrication.

Buy against a defined scope and review schedule

Ask the manufacturer for a proposal identifying device and assembly ratings, construction, enclosure, feeder provisions, metering, exclusions and project-specific documentation. Where UL 891 is specified for an appropriate switchboard, verify the proposed assembly listing and its scope rather than assuming compliance from a component label. Compare exceptions and approved alternatives before awarding the order.

Set milestones for design inputs, shop drawing review, component release, inspection, shipping and site commissioning, with ownership for each. Specify drawings, test records, manuals and labeling at turnover. Component availability and changes after approval can affect the schedule; qualified personnel must perform installation, testing and energization under an approved project plan.

LET'S BUILD SOMETHING RELIABLE — 03

Ready to talk
switchgear?

Tell us about the new equipment your project needs. Include as much or as little detail as you have today.

(951) 403-5738

CALL TO DISCUSS YOUR PROJECT

PROJECT INQUIRY

Request a quote

01 — 04

This opens your email app for you to review and send. Add any details that do not transfer, or call if you do not have an email app configured.

Request a quote