BUILT IN THE USA. READY FOR YOUR PROJECT.
Motor Control Centers: Protection and Coordination
A motor control center (MCC) groups motor starters and related feeder equipment in one lineup, so one protection decision can affect several processes.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A motor control center (MCC) groups motor starters and related feeder equipment in one lineup, so one protection decision can affect several processes. For a new MCC, engineers and purchasers need to align motor starting requirements with fault duty and the upstream distribution system. A useful specification identifies what must keep running, what must trip, and who will verify the design.
Start with the sources and motor loads
Provide a current one-line diagram showing the source, transformer, upstream protective devices, MCC feeder and any alternate supply. The study engineer needs transformer impedance, feeder conductor details, source fault data and operating configurations. Motors can contribute to fault current, so the motor schedule matters to the short-circuit study as well as equipment selection.
For each motor, supply its nameplate data, starting method, expected acceleration time, duty and process importance. Identify variable-frequency drives, soft starters and simultaneous starting sequences. A long-starting pump and a lightly loaded fan may need different protective characteristics even when their nameplate horsepower is similar. Include planned spare units and likely future loads.
Separate interrupting capacity from assembly fault duty
The available short-circuit current at the MCC depends on the system configuration and must be compared with the proposed assembly's short-circuit current rating at the applicable voltage. A breaker's interrupting rating describes its ability to interrupt fault current; it does not, by itself, establish the rating of the entire lineup or each motor starter combination.
Ask for the MCC rating and any conditions attached to it, including specific upstream devices, fuse classes or component combinations. Bus bracing and any relevant withstand duration also need to suit the protection scheme. A substitution that looks equivalent on a parts list may invalidate the documented combination, so request engineering review before approving it.
Choose branch protection around the motor
A motor branch commonly combines a disconnect, short-circuit protective device, contactor and overload protection. The short-circuit device addresses high fault currents, while the overload function responds to sustained motor overcurrent. A contactor is a control device, not a substitute for a properly selected fault interrupter. The complete combination must be suitable for its application.
Fused and circuit-breaker-based combinations can differ in clearing characteristics, coordination options and post-trip restoration requirements. Drive and soft-starter inputs may have their own specified protective-device combinations. Compare the actual device types and settings ranges, not simply the number of buckets. Confirm that motor starting current and duration are considered without compromising required protection.
Define the coordination objective
When a single motor branch faults, the owner may want its protective device to operate without unnecessarily removing power from adjacent motors. The study engineer compares branch and upstream device characteristics over the relevant current range, including motor-starting behavior. Time-current curves are useful, but their plots alone do not prove selective operation at every fault level.
Where available, obtain applicable manufacturer coordination data for the proposed device pairs and document the range in which selectivity is supported. Faster clearing can reduce exposure in some scenarios, while deliberate delays may improve coordination but affect incident energy and equipment duty. The engineer must evaluate these competing objectives for each operating condition rather than promise perfect selectivity.
Make study and control interfaces part of the order
A quote request to a direct manufacturer of new assemblies should identify the required device types, fault duty, enclosure conditions, feeder entry and any project-specific listing or standards requirements. Specify which motor units need remote start, status, trip alarms or communications, and provide the control-voltage and terminal interface requirements. These choices affect unit space and wiring.
Ask for a device schedule, proposed one-line, elevations, wiring diagrams, rating information and documented exceptions. Establish who supplies the short-circuit, coordination and arc-flash studies; who approves settings; and who provides field wiring and testing. The manufacturer's drawings provide equipment data, but they are not automatically a complete system study.
Coordinate reviews through commissioning
Set a review sequence that allows the study engineer to evaluate proposed devices before component purchasing and fabrication decisions are finalized. Track revisions to source data, motor loads and device selections because each can change the study or the equipment design. Discuss component availability, approval turnaround and testing requirements when establishing the project schedule, and confirm delivery expectations in the quotation.
Define factory inspection and functional-test scope, witness needs and the records required for turnover. Before energization, qualified personnel should verify installation, approved settings and applicable test results under the owner's safety procedures and manufacturer instructions. Retain final drawings, study results, settings and device information so later changes can be evaluated against the original protection scheme.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT