BUILT IN THE USA. READY FOR YOUR PROJECT.
35 kV Switchgear: Protection and Fault-Duty Review
A 35 kV system designation is a starting point, not a complete switchgear specification.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A 35 kV system designation is a starting point, not a complete switchgear specification. The owner, engineer, utility and manufacturer need to establish both normal operating conditions and the faults the equipment must handle. For a new assembly, the useful purchasing question is whether the proposed devices, insulation, bus and protection scheme work together for the actual system and its foreseeable operating states.
Establish the voltage and insulation basis
Give the manufacturer the nominal system voltage, highest expected operating voltage, frequency, grounding method and service conditions. The engineer must select an appropriate equipment voltage class and insulation levels; the number in a project title alone does not establish those ratings. Switching and lightning surge exposure, altitude and contamination can affect the insulation coordination review.
Identify whether the lineup is connected directly to a utility supply, a transformer, generation or a combination. Provide applicable project standards and the utility’s interconnection requirements. Ask which construction and protective devices are suitable for that basis; availability at the requested voltage class is subject to a project-specific engineering and manufacturing review.
Describe every credible fault source
A short-circuit study starts with an up-to-date one-line diagram and source data. Obtain utility maximum and minimum fault contributions and associated X/R information where available, plus transformer impedance, generator and motor contributions, cable characteristics and any planned expansion. Record normal, alternate and parallel-source configurations rather than assuming that a single operating state governs.
The engineer evaluates available fault current at each relevant bus and feeder, including the future system configuration. Maximum duty helps determine equipment capability; minimum faults matter because protective devices must still detect and clear them. If utility data or operating assumptions change, the calculated duty and protective scheme may need to be revisited.
Compare breaking duty with assembly withstand
A breaker’s interrupting capability addresses its ability to clear specified fault duty, while the assembly and bus also need appropriate short-circuit and short-time withstand capability. Check the applicable current, duration and asymmetry requirements together. A high interrupting value by itself does not establish that the complete lineup can withstand the forces and heating until a fault is cleared.
Duty depends on more than a simple symmetrical current figure. The engineer should review the applicable standard, X/R assumptions, clearing time and any special switching duties with the manufacturer. Compare the proposed breaker, bus, connections and overall assembly on the same study basis, and document any limitations or exceptions in the quote.
Coordinate sensing, relays and clearing
Protection needs to distinguish a feeder fault from a fault on the main bus or incoming source. The engineer can compare relay time-current characteristics with upstream utility protection and downstream devices over the relevant fault range. Faster clearing may reduce damage or exposure, but aggressive settings can sacrifice selectivity and disconnect more load than necessary.
Specify current transformer ratios, accuracy and burden appropriate to the protection functions, including the risk of saturation during faults. Ground-fault sensing must suit the system grounding arrangement and the intended sensitivity. Where differential protection is considered, account for additional current transformers, wiring, relay inputs and testing; its benefits and complexity depend on the actual protection zones.
Resolve control and safety interfaces
A protection scheme also depends on reliable trip power, breaker trip circuits and the signals exchanged with upstream equipment. Define the control-power source, monitoring, loss-of-power response, interlocks and communication points. Assign responsibility for utility approvals, relay settings and any transfer, generator or remote-control logic so that a device schedule is not mistaken for a complete operating design.
Ask a qualified study provider to evaluate arc-flash exposure using the actual system configuration and proposed clearing behavior. Coordination and incident-energy objectives can conflict, and either study may require revision after settings or source conditions change. Field installation, testing and energization belong to qualified personnel following applicable safety procedures and manufacturer instructions.
Make the quote and submittal review actionable
Send the direct manufacturer the one-line, fault and coordination studies if available, device preferences, load and feeder schedules, grounding information, enclosure conditions and required drawings. Identify which party provides relays, instrument transformers, settings and field terminations. If domestic component origin matters, specify the evidence needed and confirm availability for each item rather than assuming every component qualifies.
Request an annotated one-line, device and instrument-transformer schedules, stated equipment ratings, protection interfaces, applicable test records and a list of exceptions. Agree on who reviews settings and witnesses factory checks, and who completes site testing and final acceptance. Allow schedule time for utility data, study revisions, drawing approval and component procurement; delivery depends on those project-specific steps.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT