BUILT IN THE USA. READY FOR YOUR PROJECT.
Transfer Switch vs. Switchgear
A transfer switch selects between power sources; switchgear manages and protects the distribution of electrical power.
DIRECT FROM THE MANUFACTURER / NEW EQUIPMENT

THE MANUFACTURER’S PERSPECTIVE — 02
A transfer switch selects between power sources; switchgear manages and protects the distribution of electrical power. They solve different problems, although a facility may need both in the same one-line diagram. For an owner, engineer or contractor, the important purchase decision is how source selection, protective devices and downstream loads work together—not which label sounds more capable.
Different jobs in the power system
A transfer switch connects a designated load to one source or another. An automatic transfer switch, or ATS, monitors source conditions and commands a transfer according to its approved control sequence. It does not create backup power, and an ordinary open-transition transfer includes a break in supply; loads requiring no interruption may need a separately engineered solution.
Switchgear is an assembly of switching and protective equipment arranged to control and distribute power through buses and feeders. It can incorporate breakers, protective relays, metering and control functions, depending on the design. Some switchgear arrangements can perform source-transfer functions, so an ATS is not necessarily a separate enclosure in every engineered system.
Where the equipment connects
One arrangement places a transfer switch between normal and alternate sources and a downstream distribution section. Another transfers only selected critical feeders while other loads remain on normal power. A main-tie-main switchgear scheme may provide a different approach to transferring buses. The right arrangement depends on the continuity objective, source capacity, operating philosophy and applicable requirements.
Show both source paths, disconnecting and protective devices, transfer points, and each load group on the one-line. Identify the generator start signal, available status contacts, alarm points and control-power sources. Assign ownership of wiring between equipment suppliers, the generator provider and the installing contractor so that a missing control interface does not delay commissioning.
Choose the transfer behavior deliberately
Open transition separates the sources during transfer but briefly interrupts the load. Closed transition can momentarily parallel acceptable sources and may reduce that interruption, but it requires suitable synchronization, controls and interconnection approval. The engineer and utility should establish whether paralleling is permissible; it should never be assumed from a generic product description.
Specify source-acceptance thresholds, transfer and retransfer timing, loss-of-control-power behavior and any load-shedding sequence. For generator supply, assess starting and running loads, including motor inrush, against generator performance. A bypass-isolation arrangement may support maintenance without removing the load from its power path, but adds equipment, space and project-specific operating complexity.
Coordinate protection, neutral and grounding
A transfer device’s continuous-current rating alone does not establish fault suitability. The engineer should evaluate the available fault current from each source and the transfer equipment’s withstand and closing rating in conjunction with the applicable upstream protective device and its clearing characteristics. Switchgear interrupting and assembly duties must also fit the available fault currents and study assumptions.
An ATS is not automatically a substitute for feeder overcurrent protection; some transfer assemblies may include protection when specifically designed and rated for it. Determine whether the neutral is switched or solid, and coordinate generator grounding, bonding and ground-fault sensing with that choice. The responsible engineer must resolve these interfaces for the actual system and applicable code.
Prepare a useful purchase scope
Provide the one-line, load schedule, system voltage and phase configuration, current requirements, source fault information, feeder list and desired operating sequence. Add room dimensions, cable-entry directions, termination quantities, enclosure environment and required access. Identify essential loads and future capacity separately so proposed equipment can be evaluated against actual priorities rather than an assumed margin.
Ask the direct American manufacturer of new switchgear and power-distribution assemblies to identify what it will furnish for the transfer interface and whether a separate ATS is included, coordinated or supplied by others. Confirm applicable standards and project-specific listings, including UL 1008 where applicable to transfer equipment. If domestic component origin is specified, request verification of actual sourcing and availability.
Plan review, testing and turnover
Compare proposals using scope boundaries, device schedules, control schematics, physical drawings, exceptions and required documentation—not the enclosure description alone. Decide who provides protection settings and study updates, generator controls, field connections and acceptance testing. The submittal should identify interface terminals, operating states, alarms and the test criteria for the combined system.
Build the schedule around design approval, component availability, fabrication, factory checks, delivery and site commissioning rather than a promised generic lead time. Coordinate utility review and any outage windows early. Qualified electrical personnel should perform installation, testing and energization under site procedures, applicable codes and manufacturer instructions. This approach supports projects in San Antonio, South Texas and nationwide.
LET'S BUILD SOMETHING RELIABLE — 03
Ready to talk
switchgear?
Tell us about the new equipment your project needs. Include as much or as little detail as you have today.
(951) 403-5738CALL TO DISCUSS YOUR PROJECT